한국표준정보망(KSSN)

해외표준검색/구입

해외표준  >  해외표준검색/구입

상세정보
표준번호 ASTM E18:17e1
상태 Historical
표준명 Standard Test Methods for Rockwell Hardness of Metallic Materials
발행일자 2017-07-01
적용범위

1.1 These test methods cover the determination of the Rockwell hardness and the Rockwell superficial hardness of metallic materials by the Rockwell indentation hardness principle. This standard provides the requirements for Rockwell hardness machines and the procedures for performing Rockwell hardness tests.

1.2 This standard includes additional requirements in annexes:

Verification of Rockwell Hardness Testing Machines

Annex A1

Rockwell Hardness Standardizing Machines

Annex A2

Standardization of Rockwell Indenters

Annex A3

Standardization of Rockwell Hardness Test Blocks

Annex A4

Guidelines for Determining the Minimum Thickness of a
 Test Piece

Annex A5

Hardness Value Corrections When Testing on Convex
 Cylindrical Surfaces

Annex A6

1.3 This standard includes nonmandatory information in appendixes which relates to the Rockwell hardness test.

List of ASTM Standards Giving Hardness Values Corresponding
 to Tensile Strength

Appendix X1

Examples of Procedures for Determining Rockwell
 Hardness Uncertainty

Appendix X2

1.4 Units—At the time the Rockwell hardness test was developed, the force levels were specified in units of kilograms-force (kgf) and the indenter ball diameters were specified in units of inches (in.). This standard specifies the units of force and length in the International System of Units (SI); that is, force in Newtons (N) and length in millimeters (mm). However, because of the historical precedent and continued common usage, force values in kgf units and ball diameters in inch units are provided for information and much of the discussion in this standard refers to these units.

1.5 The test principles, testing procedures, and verification procedures are essentially identical for both the Rockwell and Rockwell superficial hardness tests. The significant differences between the two tests are that the test forces are smaller for the Rockwell superficial test than for the Rockwell test. The same type and size indenters may be used for either test, depending on the scale being employed. Accordingly, throughout this standard, the term Rockwell will imply both Rockwell and Rockwell superficial unless stated otherwise.

1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

핸드북 NO. 03.01
이력정보
표준번호 승인일 상태 상세보기
ASTM E18:18a 2018-10-01 Active 상세보기
ASTM E18:18 2018-07-01 Historical 상세보기
ASTM E18:17 2017-07-01 Historical
ASTM E18:17e1 2017-07-01 Historical
ASTM E18:16 2016-05-01 Historical 상세보기
ASTM E18:15 2015-02-01 Historical 상세보기
ASTM E18:14a 2014-10-01 Historical 상세보기
ASTM E18:14 2014-01-01 Historical 상세보기
ASTM E18:12 2012-12-01 Historical 상세보기
ASTM E18:11 2011-11-01 Historical 상세보기
ASTM E18:08b 2008-12-01 Historical 상세보기
ASTM E18:08a 2008-05-15 Historical 상세보기
ASTM E18:08 2008-01-15 Historical 상세보기
ASTM E18:07 2007-04-01 Historical 상세보기
ASTM E18:05e1 2005-04-01 Historical 상세보기
ASTM E18:05 2005-02-01 Historical 상세보기
ASTM E18:03 2003-06-10 Historical 상세보기
ASTM E18:03e1 2003-06-10 Historical 상세보기
ASTM E18:02 2002-01-10 Historical 상세보기
ASTM E18:00 2002-01-10 Historical 상세보기
구매정보
언어 파일(PDF) 출력(인쇄)  
영어 장바구니 담기

※ REDLINE : ※ 레드라인 : 최신 유효표준(Active)과 직전 구판표준(Historiccal)의 변경 내용을 포함하고 있는 버전. 구입 시 유효표준과 레드라인 두 개 파일을 제공