관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
분야 | ISO/TC 2/SC 14 : Surface coatings |
---|---|
적용범위 | ISO 10684:2004 specifies material, process, dimensional and some performance requirements for hot dip spun galvanized coatings applied to coarse threaded steel fasteners from M8 up to and including M64 and for property classes up to and including 10.9 for bolts, screws and studs and 12 for nuts. It is not recommended to hot dip galvanize threaded fasteners in diameters smaller than M8 and/or with pitches below 1,25 mm. ISO 10684:2004 primarily concerns the spun hot dip galvanizing of threaded steel fasteners, but it may also be applied to other threaded steel parts. The specifications given in this document may also be applied to non-threaded steel parts such as washers. |
국제분류(ICS)코드 |
25.220.40 : 금속 도장
21.060.01 : 조임쇠 일반 |
페이지수 | 20 |
Edition | 1 |
No. | 표준번호 | 표준명 | 발행일 | 상태 |
---|---|---|---|---|
1 | ISO 10684:2004/Cor 1:2008 | 2008-07-01 | 표준 | |
2 | ISO 10684:2004 | Fasteners — Hot dip galvanized coatings | 2004-07-12 | 표준 |
관련상품이 존재하지 않습니다.
ISO 10684:2004/Cor 1:2008 - 상세보기
ISO 1461:2009 - Hot dip galvanized coatings on fabricated iron and steel articles — Specifications and test methods 상세보기
IEC 60896-21:2004 - Stationary lead-acid batteries - Part 21: Valve regulated types - Methods of test 상세보기
ISO 10816-3:2009/Amd 1:2017 - Mechanical vibration — Evaluation of machine vibration by measurements on non-rotating parts — Part 3: Industrial machines with nominal power above 15 kW and nominal speeds between 120 r/min and 15 000 r/min when measured in situ — Amendment 1 상세보기
IEC 60072-3:1994 - Dimensions and output series for rotating electrical machines - Part 3: Small built-in motors - Flange numbers BF10 to BF50 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기