사업자등록증
해외표준
FAQ
장바구니
고객센터
해외표준 상세정보
관심표준 등록 : 표준업데이트 시 알림서비스
제공형태 더보기-
표준
판매
ISO 15614-7:2016
Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 7: Overlay welding- 발행일 : 2016-10-07
- 발행기관 : ISO
상세정보
| 분야 | ISO/TC 44/SC 10 : Quality management in the field of welding |
|---|---|
| 적용범위 | ISO 15614-7:2016 specifies how a preliminary welding procedure specification for overlay welding is qualified by welding procedure tests. ISO 15614-7:2016 defines the conditions for execution of welding procedure tests and the range of qualification for welding procedures for all practical welding operations within the range of variables listed in Clause 8. ISO 15614-7:2016 applies to all welding processes suitable for overlay welding. In situations where qualification is carried out on a pre-production test piece, the qualification is performed in accordance with ISO 15613 except that, as far as possible, the testing is according to this part of ISO 15614. Building up and repair of parent metal is covered by ISO 15613 or ISO 15614‑1. This edition of ISO 15614‑7 is applicable to all new welding procedure qualification tests. It does not invalidate previous welding procedure tests made in accordance with previous editions of this part of ISO 15614. Where additional tests are required by the present edition, it is only necessary that those additional tests be carried out on a test piece made in accordance with the existing WPS and this part of ISO 15614. If buttering is used for welding between dissimilar materials, the welding procedure is qualified in accordance with ISO 15614‑1. This buttering may be required for weld combining different material structure or properties, e.g. joining martensitic steels or ferritic steels with austenitic steels. Additional tests may be required by application standards. |
| 국제분류(ICS)코드 | 25.160.10 : 용접 및 용접공의 자질 |
| 페이지수 | 22 |
| Edition | 2 |
이력정보
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 15614-7:2016상세보기 | Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 7: Overlay welding | 2016-10-07 | 표준 |
| 2 | ISO 15614-7:2007상세보기 | Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 7: Overlay welding | 2007-06-14 | 구판 |
관련상품
- ISO/FDIS 15614-2 - Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 2: Arc welding of aluminium and its alloys
- ISO/DIS 15614-9 - Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 9: Underwater hyperbaric wet welding
- ISO/DIS 15614-13 - Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 13: Resistance butt and flash welding
- ISO/DIS 15614-6 - Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 6: Arc welding of copper and its alloys
- ISO/FDIS 15614-11 - Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 11: Electron and laser beam welding
다른 사람이 함께 구입한 상품
- ISO 17662:2016 - Welding — Calibration, verification and validation of equipment used for welding, including ancillary activities
- ISO 148-1:2016 - Metallic materials — Charpy pendulum impact test — Part 1: Test method
- ISO 17639:2003 - Destructive tests on welds in metallic materials — Macroscopic and microscopic examination of welds
- ISO 15792-3:2011 - Welding consumables — Test methods — Part 3: Classification testing of positional capacity and root penetration of welding consumables in a fillet weld
- ISO 15614-3:2008 - Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 3: Fusion welding of non-alloyed and low-alloyed cast irons
추천 상품
- IEC TS 63134:2020 - Active assisted living (AAL) use cases
- IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification
- KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs)
- KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs)
- KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스
제공형태 닫기
PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)보안PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능PRINT :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)BOOK :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)ZIP :
압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)CD/DVD :
직접 파일 다운로드 및 인쇄(마이페이지 확인)DB :
별도 정보 제공HARDCOPY :
해외 배송 상품, 최대 3주 소요바인더 :
바인더 우편발송, 2~3일 소요온라인구독 :
WEB 접속 후 실시간 열람, 출력(1년간)