사업자등록증
해외표준
FAQ
장바구니
고객센터
해외표준 상세정보
관심표준 등록 : 표준업데이트 시 알림서비스
제공형태 더보기-
표준
판매
ISO 11124-4:2018
Preparation of steel substrates before application of paints and related products — Specifications for metallic blast-cleaning abrasives — Part 4: Low-carbon cast-steel shot- 발행일 : 2018-08-23
- 발행기관 : ISO
상세정보
| 분야 | ISO/TC 35/SC 12 : Preparation of steel substrates before application of paints and related products |
|---|---|
| 적용범위 | This document specifies requirements for 12 grades of low-carbon cast-steel shot abrasive, as supplied for blast-cleaning processes. Values are specified for hardness, density, defect/structural requirements and chemical composition. The requirements specified in this document apply to abrasives supplied in the "new" condition only. They do not apply to abrasives either during or after use. Test methods for metallic blast-cleaning abrasives are given in the various parts of ISO 11125. Low-carbon cast-steel shot abrasives are used in both static and site blasting equipment. They are most often selected where a facility exists for recovery and re-use of the abrasive. NOTE 1 Information on commonly referenced national standards for metallic abrasives and their approximate relationship with ISO 11124 is given in Annex A. NOTE 2 Although this document has been developed specifically to meet requirements for preparation of steelwork, the properties specified will generally be appropriate for use when preparing other material surfaces, or components, using blast-cleaning techniques. These techniques are described in ISO 8504-2. |
| 국제분류(ICS)코드 | 25.220.10 : 블라스팅 |
| 페이지수 | 7 |
| Edition | 2 |
이력정보
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 11124-4:2018상세보기 | Preparation of steel substrates before application of paints and related products — Specifications for metallic blast-cleaning abrasives — Part 4: Low-carbon cast-steel shot | 2018-08-23 | 표준 |
| 2 | ISO 11124-4:1993상세보기 | Preparation of steel substrates before application of paints and related products — Specifications for metallic blast-cleaning abrasives — Part 4: Low-carbon cast-steel shot | 1993-12-02 | 구판 |
관련상품
- ISO/FDIS 11124-6 - Preparation of steel substrates before application of paints and related products — Specifications for metallic blast-cleaning abrasives — Part 6: Stainless steel (shot and irregulars)
- ISO/PRF 11124-7 - Preparation of steel substrates before application of paints and related products — Specifications for metallic blast-cleaning abrasives — Part 7: High chromium white cast iron grit
- ISO 11124-2:2018 - Preparation of steel substrates before application of paints and related products — Specifications for metallic blast-cleaning abrasives — Part 2: Chilled-iron grit
- ISO 11124-1:2018 - Preparation of steel substrates before application of paints and related products — Specifications for metallic blast-cleaning abrasives — Part 1: General introduction and classification
- ISO 11124-3:2018 - Preparation of steel substrates before application of paints and related products — Specifications for metallic blast-cleaning abrasives — Part 3: High-carbon cast-steel shot and grit
다른 사람이 함께 구입한 상품
- ISO 12944-6:2018 - Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 6: Laboratory performance test methods
- ISO 2063-2:2017 - Thermal spraying — Zinc, aluminium and their alloys — Part 2: Execution of corrosion protection systems
- DIN EN 10163-1:2005-03 - Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 1: General requirements
- ISO 9013:2017 - Thermal cutting — Classification of thermal cuts — Geometrical product specification and quality tolerances
- ISO 12944-5:2019 - Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 5: Protective paint systems
추천 상품
- IEC TS 63134:2020 - Active assisted living (AAL) use cases
- IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification
- KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs)
- KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs)
- KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스
제공형태 닫기
PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)보안PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능PRINT :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)BOOK :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)ZIP :
압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)CD/DVD :
직접 파일 다운로드 및 인쇄(마이페이지 확인)DB :
별도 정보 제공HARDCOPY :
해외 배송 상품, 최대 3주 소요바인더 :
바인더 우편발송, 2~3일 소요온라인구독 :
WEB 접속 후 실시간 열람, 출력(1년간)