사업자등록증
해외표준
FAQ
장바구니
고객센터
해외표준 상세정보
관심표준 등록 : 표준업데이트 시 알림서비스
제공형태 더보기-
표준
판매
ISO 8178-3:2019
Reciprocating internal combustion engines — Exhaust emission measurement — Part 3: Test procedures for measurement of exhaust gas smoke emissions from compression ignition engines using a filter type smoke meter- 발행일 : 2019-01-30
- 발행기관 : ISO
상세정보
| 분야 | ISO/TC 70/SC 8 : Exhaust gas emission measurement |
|---|---|
| 적용범위 | This document specifies a method for the measurement of smoke from exhaust gas of reciprocating internal combustion (RIC) engines at a steady state condition. The method evaluates the soot content by measurement of the blackening of a filter and derivation of black carbon mass concentration (mg/m3) from FSN. Where necessary, individual requirements may be specified for particular engine applications. This document is applicable to RIC engines for mobile, transportable and stationary use, excluding engines for on-road transport of passengers and goods. It can be applied to engines for non-road use, e.g. for earth-moving machines, generating sets and for other applications. For engines used in machinery covered by additional requirements (e.g. occupational health and safety regulations, regulations for power plants) additional test conditions and special evaluation methods can apply. |
| 국제분류(ICS)코드 |
27.020 : 내연기관
13.040.50 : 수송 배기가스 방사 |
| 페이지수 | 11 |
| Edition | 2 |
이력정보
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 8178-3:2019상세보기 | Reciprocating internal combustion engines — Exhaust emission measurement — Part 3: Test procedures for measurement of exhaust gas smoke emissions from compression ignition engines using a filter type smoke meter | 2019-01-30 | 표준 |
| 2 | ISO 8178-3:1994상세보기 | Reciprocating internal combustion engines — Exhaust emission measurement — Part 3: Definitions and methods of measurement of exhaust gas smoke under steady-state conditions | 1994-08-25 | 구판 |
관련상품
- ISO 8178-1:2017/DAmd 1 - Reciprocating internal combustion engines — Exhaust emission measurement — Part 1: Test-bed measurement systems of gaseous and particulate emissions — Amendment 1: Update of certain instrument and measurement provisions and of the carbon flow check
- ISO/DIS 8178-1 - Reciprocating internal combustion engines — Exhaust emission measurement — Part 1: Test-bed measurement of gaseous and particulate exhaust emissions
- ISO 8178-4:2017/DAmd 1 - Reciprocating internal combustion engines — Exhaust emission measurement — Part 4: Steady-state and transient test cycles for different engine applications — Amendment 1: Update of data evaluation and calculation provisions, the molar based emission calculations and of the engine control area for E3 and E5 test cycle
- ISO 8178-10:2002 - Reciprocating internal combustion engines — Exhaust emission measurement — Part 10: Test cycles and test procedures for field measurement of exhaust gas smoke emissions from compression ignition engines operating under transient conditions
- ISO 8178-11:2006 - Reciprocating internal combustion engines — Exhaust emission measurement — Part 11: Test-bed measurement of gaseous and particulate exhaust emissions from engines used in nonroad mobile machinery under transient test conditions
다른 사람이 함께 구입한 상품
- ISO 8178-8:2015 - Reciprocating internal combustion engines — Exhaust emission measurement — Part 8: Engine group determination
- ISO 8178-6:2018 - Reciprocating internal combustion engines — Exhaust emission measurement — Part 6: Report of measuring results and test
- ISO 8178-7:2015 - Reciprocating internal combustion engines — Exhaust emission measurement — Part 7: Engine family determination
- ISO 8178-5:2015 - Reciprocating internal combustion engines — Exhaust emission measurement — Part 5: Test fuels
- ISO 8178-2:2008 - Reciprocating internal combustion engines — Exhaust emission measurement — Part 2: Measurement of gaseous and particulate exhaust emissions under field conditions
추천 상품
- IEC TS 63134:2020 - Active assisted living (AAL) use cases
- IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification
- KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs)
- KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs)
- KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스
제공형태 닫기
PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)보안PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능PRINT :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)BOOK :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)ZIP :
압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)CD/DVD :
직접 파일 다운로드 및 인쇄(마이페이지 확인)DB :
별도 정보 제공HARDCOPY :
해외 배송 상품, 최대 3주 소요바인더 :
바인더 우편발송, 2~3일 소요온라인구독 :
WEB 접속 후 실시간 열람, 출력(1년간)