사업자등록증
해외표준
FAQ
장바구니
고객센터
해외표준 상세정보
관심표준 등록 : 표준업데이트 시 알림서비스
제공형태 더보기-
표준
판매
ISO 3506-7:2024
Fasteners — Mechanical properties of corrosion-resistant stainless steel fasteners — Part 7: Flat washers with specified grades and property classes- 발행일 : 2024-07-25
- 발행기관 : ISO
상세정보
| 분야 | ISO/TC 2 : Fasteners |
|---|---|
| 적용범위 | This document specifies the mechanical and physical properties of flat washers made of corrosion resistant austenitic, ferritic and duplex stainless steels, designed to be used in bolted joints in combination with bolts, screws, studs and nuts with specified grades and property classes in accordance with ISO 3506-1 and ISO 3506-2. These types of washers are also used with other stainless steel fasteners such as screws forming their own mating thread (see e.g. ISO 3506-4). ISO 3506-6 provides general rules and additional technical information on suitable stainless steels and their properties (detailed properties of stainless steel grades, corrosion behaviour with regards to pitting, crevice and intergranular corrosion, magnetic properties, etc.) WARNING — Washers conforming to the requirements of this document are tested at the ambient temperature range of 10 °C to 35 °C and are used in applications ranging from –20 °C to +150 °C. However, these washers are also used outside this range down to –196 °C and up to +300 °C for specific applications. It is possible that they do not retain the specified mechanical and physical properties at lower and/or elevated temperatures. Therefore, it is the responsibility of the user to determine the appropriate choices based on the service environment conditions of the assembly (see also Clauses 6 and 7). This document applies to the following flat non-captive and captive washers with thickness 0,2 mm to 6 mm (see 5.1): — plain washers and flat washers (with or without knurls, ribs or chamfers), — square washers, — square hole washers, — shaped plates. The term “washer” is used in the following for all types of washers and plates within the scope of this document. This document does not specify requirements for functional properties such as weldability. |
| 국제분류(ICS)코드 | 21.060.30 : 와셔. 잠금 장치 |
| 페이지수 | 14 |
| Edition | 1 |
이력정보
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 3506-7:2024상세보기 | Fasteners — Mechanical properties of corrosion-resistant stainless steel fasteners — Part 7: Flat washers with specified grades and property classes | 2024-07-25 | 표준 |
관련상품
- ISO 3506-1:2020 - Fasteners — Mechanical properties of corrosion-resistant stainless steel fasteners — Part 1: Bolts, screws and studs with specified grades and property classes
- ISO 3506-2:2020 - Fasteners — Mechanical properties of corrosion-resistant stainless steel fasteners — Part 2: Nuts with specified grades and property classes
- ISO 3506-6:2020 - Fasteners — Mechanical properties of corrosion-resistant stainless steel fasteners — Part 6: General rules for the selection of stainless steels and nickel alloys for fasteners
- ISO 3506-5:2022 - Fasteners — Mechanical properties of corrosion-resistant stainless steel fasteners — Part 5: Special fasteners (also including fasteners from nickel alloys) for high temperature applications
- ISO 3506-3:2025 - Fasteners — Mechanical properties of corrosion resistant stainless steel fasteners — Part 3: Set screws (and similar fasteners not under tensile stress) with specified grades and hardness classes
다른 사람이 함께 구입한 상품
- 함께 구입한 상품이 존재하지 않습니다.
추천 상품
- IEC TS 63134:2020 - Active assisted living (AAL) use cases
- IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification
- KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs)
- KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs)
- KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스
제공형태 닫기
PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)보안PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능PRINT :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)BOOK :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)ZIP :
압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)CD/DVD :
직접 파일 다운로드 및 인쇄(마이페이지 확인)DB :
별도 정보 제공HARDCOPY :
해외 배송 상품, 최대 3주 소요바인더 :
바인더 우편발송, 2~3일 소요온라인구독 :
WEB 접속 후 실시간 열람, 출력(1년간)