사업자등록증
해외표준
FAQ
장바구니
고객센터
해외표준 상세정보
관심표준 등록 : 표준업데이트 시 알림서비스
제공형태 더보기-
표준
판매
ISO 18563-3:2024
Non-destructive testing — Characterization and verification of ultrasonic phased array equipment — Part 3: Complete systems- 발행일 : 2024-05-01
- 발행기관 : ISO
상세정보
| 분야 | ISO/TC 135/SC 3 : Ultrasonic testing |
|---|---|
| 적용범위 | This document addresses ultrasonic test systems implementing array probes, for contact technique (with or without wedge) or for immersion technique, with centre frequencies in the range of 0,5 MHz to 10 MHz. This document provides methods and acceptance criteria for determining the compliance of the complete system (see 3.2). Its purpose is for the verification of the correct operation of the system prior to testing or verification of the absence of degradation of the system. The methods are not intended to prove the suitability of the system for particular applications but are intended to prove the capability of the complete system (used for an application) to operate correctly according to the settings used. Tests can be performed on individual ultrasonic beams (for phased array technique, see 9.4.4) or on resulting images (for phased array technique and total focusing technique, see 9.4.3). The tests can be limited to the functions that are intended to be used for a certain application. This document does not cover the sensitivity setting of the system for a specific application. Nor does it apply to the characterization or verification of the mechanical scanning equipment. It is intended that these items will be covered by the test procedure. This document does not address the phased array technique using tandem technique. The characterization of beams, as recommended in case of dead elements or for more in-depth knowledge of the beams, is presented in Annex A. It is not applicable for signal processing technology using arrays. NOTE Unless stated otherwise, in this document ‘TFM’ and ‘TFM technique’ refer to the total focusing technique as defined in ISO 23243, and to related techniques, see for example ISO 23865 and ISO 23234. |
| 국제분류(ICS)코드 | 19.100 : 비파괴 시험 및 기구 |
| 페이지수 | 32 |
| Edition | 2 |
이력정보
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 18563-3:2024상세보기 | Non-destructive testing — Characterization and verification of ultrasonic phased array equipment — Part 3: Complete systems | 2024-05-01 | 표준 |
| 2 | ISO 18563-3:2015상세보기 | Non-destructive testing — Characterization and verification of ultrasonic phased array equipment — Part 3: Combined systems | 2015-12-08 | 구판 |
관련상품
다른 사람이 함께 구입한 상품
- ISO 18563-1:2022 - Non-destructive testing — Characterization and verification of ultrasonic phased array equipment — Part 1: Instruments
- ISO 19285:2017 - Non-destructive testing of welds — Phased array ultrasonic testing (PAUT) — Acceptance levels
- ASTM E1065/E1065M-20 REDLINE - Standard Practice for Evaluating Characteristics of Ultrasonic Search Units
- ASTM A577/A577M-17(2023) - Standard Specification for Ultrasonic Angle-Beam Examination of Steel Plates
- ISO 18563-2:2024 - Non-destructive testing — Characterization and verification of ultrasonic phased array equipment — Part 2: Array probes
추천 상품
- IEC TS 63134:2020 - Active assisted living (AAL) use cases
- IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification
- KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs)
- KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs)
- KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스
제공형태 닫기
PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)보안PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능PRINT :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)BOOK :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)ZIP :
압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)CD/DVD :
직접 파일 다운로드 및 인쇄(마이페이지 확인)DB :
별도 정보 제공HARDCOPY :
해외 배송 상품, 최대 3주 소요바인더 :
바인더 우편발송, 2~3일 소요온라인구독 :
WEB 접속 후 실시간 열람, 출력(1년간)