한국표준정보망

회원가입 로그인 비회원(주문조회) 장바구니 이용안내

English
메뉴
검색 마이페이지 장바구니0

QUICK

닫기

TOP

해외표준 상세정보

관심표준 등록 : 표준업데이트 시 알림서비스

제공형태 더보기

  • KS

    구판

    판매

    ASTM D635-98

    Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position
    • 발행일 : 1998-07-10
    • 발행기관 : ASTM
    즐겨찾기 장바구니 담기
    닫기

    상품이 장바구니에 담겼습니다.

    장바구니로 이동

    • [영어]PDF 131,600원

    • [영어]PRINT 131,600원

상세정보

분야 08.01 : 플라스틱 (Ⅰ)
적용범위

1.1 This test method covers a small-scale laboratory screening procedure for comparing the relative rate of burning and/or extent and time of burning of self-supporting plastics in the form of bars, molded or cut from sheets, plates, or panels, and tested in the horizontal position. This test method should be used to establish relative burning characteristics of plastic materials and should not be used as a fire-hazard test method.

Note 1-Warning-During the course of combustion, gases or vapors, or both, are evolved which may be hazardous to personnel. Precaution-In addition to other precautions, adequate precautions should be taken to protect the operator.

Note 2-Additional information on materials which do not burn to the gage mark by this test may be obtained using Test Method D 3801. For tests of flexible plastics in the form of thin sheets and film, reference should be made to Test Methods D 4804. Tests on the burning rate of sheet and plate insulation are covered in Test Methods D 229. Burning characteristics, as measured by minimum oxygen to support combustion, may be determined by Test Method D 2863.

1.2 The values stated in SI units are to be regarded as the standard.

1.3 This standard should be used to measure and describe the properties of materials, products, or assemblies in response to heat and flame under controlled laboratory conditions and should not be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire risk assessment which takes into account all of the factors which are pertinent to an assessment of the fire hazard of a particular end use>.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Note 1 and 6.1.

국제분류(ICS)코드
페이지수 6
Edition 98

이력정보

No. 표준번호 표준명 발행일 상태
1 ASTM D635-22상세보기 Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position 2022-07-01 표준
2 ASTM D635-22 REDLINE상세보기 Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position 2022-07-01 표준
3 ASTM D635-18상세보기 Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position 2018-11-01 구판
4 ASTM D635-18 REDLINE상세보기 Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position 2018-11-01 구판
5 ASTM D635-14상세보기 Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position 2014-12-01 구판
6 ASTM D635-10상세보기 Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position 2010-07-01 구판
7 ASTM D635-06상세보기 Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position 2006-05-01 구판
8 ASTM D635-03상세보기 Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position 2003-07-10 구판
9 ASTM D635-98상세보기 Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position 1998-07-10 구판
10 ASTM D635-97상세보기 Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position 구판

관련상품

  • 관련상품이 존재하지 않습니다.

다른 사람이 함께 구입한 상품

  • 함께 구입한 상품이 존재하지 않습니다.

추천 상품

제공형태 닫기

  • PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)

  • 보안PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능

  • PRINT :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

  • BOOK :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

  • ZIP :

    압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)

  • CD/DVD :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)

  • DB :

    별도 정보 제공

  • HARDCOPY :

    해외 배송 상품, 최대 3주 소요

  • 바인더 :

    바인더 우편발송, 2~3일 소요

  • 온라인구독 :

    WEB 접속 후 실시간 열람, 출력(1년간)