사업자등록증
해외표준
FAQ
장바구니
고객센터
해외표준 상세정보
관심표준 등록 : 표준업데이트 시 알림서비스
제공형태 더보기-
구판
판매
ASTM D4530-00
Standard Test Method for Determination of Carbon Residue (Micro Method)- 발행일 : 2000-05-10
- 발행기관 : ASTM
상세정보
| 분야 | 05.02 : 석유제품 및 윤활유 (Ⅱ) |
|---|---|
| 적용범위 | 1.1 This test method covers the determination of the amount of carbon residue (see Note 1) formed after evaporation and pyrolysis of petroleum materials under certain conditions and is intended to provide some indication of the relative coke forming tendency of such materials. 1.2 The test results are equivalent to the Conradson Carbon Residue test (Test Method D189). Note 1-This procedure is a modification of the original method and apparatus for carbon residue of petroleum materials, where it has been demonstrated that thermogravimetry is another applicable technique. However it is the responsibility of the operator to establish operating conditions to obtain equivalent results when using thermogravimetry. 1.3 This test method is applicable to petroleum products that partially decompose on distillation at atmospheric pressure and was tested for carbon residue values of 0.10 to 30% (m/m). Samples expected to be below 0.10 weight% residue should be distilled to remove 90% (V/V) of the flask charge (see Section 9). The 10% bottoms remaining is then tested for carbon residue by this test method. 1.4 Ash-forming constituents as defined by Test Method D482, or non-volatile additives present in the sample will add to the carbon residue value and be included as part of the total carbon residue value reported. 1.5 Also in diesel fuel the presence of alkyl nitrates, such as amyl nitrate, hexyl nitrate or octyl nitrate, causes a higher carbon residue value than observed in untreated fuel, which may lead to erroneous conclusions as to the coke-forming propensity of the fuel. The presence of alkyl nitrate in the fuel may be detected by Test Method D4046. 1.6 The values stated in SI unites are to be regarded as the standard. The values given in parentheses are for information only. 1.7 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety practices and to determine the applicability of regulatory limitations prior to use. For specific hazard statements see 8.2.3 and 8.4. |
| 국제분류(ICS)코드 | |
| 페이지수 | 6 |
| Edition | 00 |
이력정보
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D4530-15(2020)상세보기 | Standard Test Method for Determination of Carbon Residue (Micro Method) | 2020-05-01 | 표준 |
| 2 | ASTM D4530-15상세보기 | Standard Test Method for Determination of Carbon Residue (Micro Method) | 2015-06-01 | 구판 |
| 3 | ASTM D4530-15 REDLINE상세보기 | Standard Test Method for Determination of Carbon Residue (Micro Method) | 2015-06-01 | 구판 |
| 4 | ASTM D4530-11상세보기 | Standard Test Method for Determination of Carbon Residue (Micro Method) | 2011-05-15 | 구판 |
| 5 | ASTM D4530-07상세보기 | Standard Test Method for Determination of Carbon Residue (Micro Method) | 2007-11-01 | 구판 |
| 6 | ASTM D4530-06e1상세보기 | Standard Test Method for Determination of Carbon Residue (Micro Method) | 2006-01-01 | 구판 |
| 7 | ASTM D4530-06상세보기 | Standard Test Method for Determination of Carbon Residue (Micro Method) | 2006-01-01 | 구판 |
| 8 | ASTM D4530-03상세보기 | Standard Test Method for Determination of Carbon Residue (Micro Method) | 2003-05-10 | 구판 |
| 9 | ASTM D4530-00상세보기 | Standard Test Method for Determination of Carbon Residue (Micro Method) | 2000-05-10 | 구판 |
관련상품
- 관련상품이 존재하지 않습니다.
다른 사람이 함께 구입한 상품
- 함께 구입한 상품이 존재하지 않습니다.
추천 상품
- IEC TS 63134:2020 - Active assisted living (AAL) use cases
- IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification
- KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs)
- KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs)
- KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스
제공형태 닫기
PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)보안PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능PRINT :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)BOOK :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)ZIP :
압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)CD/DVD :
직접 파일 다운로드 및 인쇄(마이페이지 확인)DB :
별도 정보 제공HARDCOPY :
해외 배송 상품, 최대 3주 소요바인더 :
바인더 우편발송, 2~3일 소요온라인구독 :
WEB 접속 후 실시간 열람, 출력(1년간)