한국표준정보망

회원가입 로그인 비회원(주문조회) 장바구니 이용안내

English
메뉴
검색 마이페이지 장바구니0

QUICK

닫기

TOP

해외표준 상세정보

관심표준 등록 : 표준업데이트 시 알림서비스

제공형태 더보기

  • KS

    구판

    판매

    ASTM D3171-99(2004)

    Standard Test Methods for Constituent Content of Composite Materials
    • 발행일 : 2004-11-01
    • 발행기관 : ASTM
    즐겨찾기 장바구니 담기
    닫기

    상품이 장바구니에 담겼습니다.

    장바구니로 이동

    • [영어]PDF 131,600원

    • [영어]PRINT 131,600원

상세정보

분야 15.03 : 공간시물레이션; 항공우주재료; 고율섬유와 합성물
적용범위

1.1 These test methods determine the constituent content of composite materials by one of two approaches. Method I physically removes the matrix by digestion or ignition by one of seven procedures, leaving the reinforcement essentially unaffected and thus allowing calculation of reinforcement or matrix content (by weight or volume) as well as percent void volume. Method II, applicable only to laminate materials of known fiber areal weight, calculates reinforcement or matrix content (by weight or volume) based on the measured thickness of the laminate. Method II is not applicable to the measurement of void volume.

1.1.1 These test methods are primarily intended for two-part composite material systems. However, special provisions can be made to extend these test methods to filled material systems with more than two constituents, though not all test results can be determined in every case.

1.1.2 The procedures contained within have been designed to be particularly effective for certain classes of polymer or metal matrices. The suggested applications are discussed in Section , as well as at the start of each procedure.

1.1.3 Method I assumes that the reinforcement is essentially unaffected by the digestion or ignition medium. A procedure for correction of the results for minor changes in the reinforcement is included. Procedures A through F are based on chemical removal of the matrix while Procedure G removes the matrix by igniting the matrix in a furnace.

1.1.4 Method II assumes that the fiber areal weight of the reinforcement material form is known or controlled to an acceptable tolerance. The presence of voids is not measured. Eqn. 1 assume zero void content to perform the calculation.

1.2 The SI units shown are considered standard.

This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See Section 9 for additional information.
국제분류(ICS)코드
페이지수 10
Edition 99(2004)

이력정보

No. 표준번호 표준명 발행일 상태
1 ASTM D3171-22상세보기 Standard Test Methods for Constituent Content of Composite Materials 2022-03-01 표준
2 ASTM D3171-22 REDLINE상세보기 Standard Test Methods for Constituent Content of Composite Materials 2022-03-01 표준
3 ASTM D3171-15상세보기 Standard Test Methods for Constituent Content of Composite Materials 2015-04-01 구판
4 ASTM D3171-15 REDLINE상세보기 Standard Test Methods for Constituent Content of Composite Materials 2015-04-01 구판
5 ASTM D3171-11상세보기 Standard Test Methods for Constituent Content of Composite Materials 2011-10-01 구판
6 ASTM D3171-09상세보기 Standard Test Methods for Constituent Content of Composite Materials 2009-04-01 구판
7 ASTM D3171-06상세보기 Standard Test Methods for Constituent Content of Composite Materials 2006-04-01 구판
8 ASTM D3171-99(2004)상세보기 Standard Test Methods for Constituent Content of Composite Materials 2004-11-01 구판
9 ASTM D3171-99상세보기 Standard Test Methods for Constituent Content of Composite Materials 1999-10-10 구판

관련상품

  • 관련상품이 존재하지 않습니다.

다른 사람이 함께 구입한 상품

  • 함께 구입한 상품이 존재하지 않습니다.

추천 상품

제공형태 닫기

  • PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)

  • 보안PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능

  • PRINT :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

  • BOOK :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

  • ZIP :

    압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)

  • CD/DVD :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)

  • DB :

    별도 정보 제공

  • HARDCOPY :

    해외 배송 상품, 최대 3주 소요

  • 바인더 :

    바인더 우편발송, 2~3일 소요

  • 온라인구독 :

    WEB 접속 후 실시간 열람, 출력(1년간)