한국표준정보망

회원가입 로그인 비회원(주문조회) 장바구니 이용안내

English
메뉴
검색 마이페이지 장바구니0

QUICK

닫기

TOP

해외표준 상세정보

관심표준 등록 : 표준업데이트 시 알림서비스

제공형태 더보기

  • KS

    구판

    판매

    ASTM D1143/D1143M-07

    Standard Test Methods for Deep Foundations Under Static Axial Compressive Load
    • 발행일 : 2007-02-01
    • 발행기관 : ASTM
    즐겨찾기 장바구니 담기
    닫기

    상품이 장바구니에 담겼습니다.

    장바구니로 이동

    • [영어]PDF 144,300원

    • [영어]PRINT 144,300원

상세정보

분야 04.08 : 토양, 석재 (Ⅰ)
적용범위

1.1 The test methods described in this standard measure the axial deflection of a vertical or inclined deep foundation when loaded in static axial compression. These methods apply to all deep foundations, referred to herein as piles, that function in a manner similar to driven piles or castinplace piles, regardless of their method of installation, and may be used for testing single piles or pile groups. The test results may not represent the long-term performance of a deep foundation.

1.2 This standard provides minimum requirements for testing deep foundations under static axial compressive load. Plans, specifications, and/or provisions prepared by a qualified engineer may provide additional requirements and procedures as needed to satisfy the objectives of a particular test program. The engineer in responsible charge of the foundation design, referred to herein as the Engineer, shall approve any deviations, deletions, or additions to the requirements of this standard.

1.3 This standard allows the following test procedures:    

Procedure AQuick Test
Procedure BMaintained Test (optional)
Procedure CLoading in Excess of Maintained Test (optional)
Procedure DConstant Time Interval Test (optional)
Procedure EConstant Rate of Penetration Test (optional)
Procedure FConstant Movement Increment Test (optional)
Procedure GCyclic Loading Test (optional)
   

1.4 Apparatus and procedures herein designated “optional” may produce different test results and may be used only when approved by the Engineer. The word “shall” indicates a mandatory provision, and the word “should” indicates a recommended or advisory provision. Imperative sentences indicate mandatory provisions.

1.5 A qualified geotechnical engineer should interpret the test results obtained from the procedures of this standard so as to predict the actual performance and adequacy of piles used in the constructed foundation. See Appendix X1 for comments regarding some of the factors influencing the interpretation of test results.

1.6 A qualified engineer shall design and approve all loading apparatus, loaded members, support frames, and test procedures. The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. This standard also includes illustrations and appendices intended only for explanatory or advisory use.

1.7 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.8 The gravitational system of inch-pound units is used when dealing with inch-pound units. In this system, the pound (lbf) represents a unit of force (weight), while the unit for mass is slugs. The rationalized slug unit is not given, unless dynamic (F=ma) calculations are involved.

1.9 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D 6026.

1.10 The method used to specify how data are collected, calculated, or recorded in this standard is not directly related to the accuracy to which the data can be applied in design or other uses, or both. How one applies the results obtained using this standard is beyond its scope.

1.11 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
국제분류(ICS)코드
페이지수 15
Edition 07

이력정보

No. 표준번호 표준명 발행일 상태
1 ASTM D1143/D1143M-20상세보기 Standard Test Methods for Deep Foundation Elements Under Static Axial Compressive Load 2020-09-15 구판
2 ASTM D1143/D1143M-20 REDLINE상세보기 Standard Test Methods for Deep Foundation Elements Under Static Axial Compressive Load 2020-09-15 구판
3 ASTM D1143/D1143M-20e1상세보기 Standard Test Methods for Deep Foundation Elements Under Static Axial Compressive Load 2020-09-15 표준
4 ASTM D1143/D1143M-07(2013)상세보기 Standard Test Methods for Deep Foundations Under Static Axial Compressive Load 2013-06-15 구판
5 ASTM D1143/D1143M-07(2013)e1상세보기 Standard Test Methods for Deep Foundations Under Static Axial Compressive Load 2013-06-15 구판
6 ASTM D1143/D1143M-07e1상세보기 Standard Test Methods for Deep Foundations Under Static Axial Compressive Load 2007-02-01 구판
7 ASTM D1143/D1143M-07상세보기 Standard Test Methods for Deep Foundations Under Static Axial Compressive Load 2007-02-01 구판

관련상품

  • 관련상품이 존재하지 않습니다.

다른 사람이 함께 구입한 상품

  • 함께 구입한 상품이 존재하지 않습니다.

추천 상품

제공형태 닫기

  • PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)

  • 보안PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능

  • PRINT :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

  • BOOK :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

  • ZIP :

    압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)

  • CD/DVD :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)

  • DB :

    별도 정보 제공

  • HARDCOPY :

    해외 배송 상품, 최대 3주 소요

  • 바인더 :

    바인더 우편발송, 2~3일 소요

  • 온라인구독 :

    WEB 접속 후 실시간 열람, 출력(1년간)