한국표준정보망

회원가입 로그인 비회원(주문조회) 장바구니 이용안내

English
메뉴
검색 마이페이지 장바구니0

QUICK

닫기

TOP

해외표준 상세정보

관심표준 등록 : 표준업데이트 시 알림서비스

제공형태 더보기

  • KS

    구판

    판매

    ASTM B26/B26M-12

    Standard Specification for Aluminum-Alloy Sand Castings
    • 발행일 : 2012-05-01
    • 발행기관 : ASTM
    즐겨찾기 장바구니 담기
    닫기

    상품이 장바구니에 담겼습니다.

    장바구니로 이동

    • [영어]PDF 144,300원

    • [영어]PRINT 144,300원

상세정보

분야 02.02 : 알루미늄 및 마그네슘 합금
적용범위

1.1 This specification covers aluminum-alloy sand castings designated as shown in Table 1.

1.2 This specification is for aluminum-alloy sand castings used in general purpose applications. It may not address the mechanical properties, integrity testing, and verification required for highly loaded or safety critical applications.

1.3 Alloy and temper designations are in accordance with ANSI H35.1/H35.1M. Unified Numbering System alloy designations are in accordance with Practice E527.

1.4 Unless the order specifies the “M” specification designation, the material shall be furnished to the inch-pound units.

1.5 For acceptance criteria for inclusion of new aluminum and aluminum alloys and their properties in this specification, see Annex A1 and Annex A2.

1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.

1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

TABLE 1 Chemical Composition Limits

Note 1—When single units are shown, these indicate the maximum amounts permitted.

Note 2—Analysis shall be made for the elements for which limits are shown in this table.

Note 3—The following applies to all specified limits in this table: For purposes of determining conformance to these limits, an observed value or a calculated value obtained from analysis shall be rounded to the nearest unit in the last right-hand place of figures used in expressing the specified limit in accordance with the rounding method of Practice E29.

Alloy AluminumComposition, (Values in Weight Percent)Others
ANSIUNSSiliconIronCopperMan-
ganese		 Magne-
sium		ChromiumNickelZincTinTitaniumEachTotal
201.0 A02010remainder0.100.154.0–5.2 0.20–0.500.15–0.55... .........0.15–0.350.05A0.10
204.0 A02040remainder0.200.354.2–5.0 0.100.15–0.35... 0.050.10 0.050.15–0.300.05 0.15
242.0 A02420remainder0.71.03.7–4.5 0.351.2–1.80.25 1.7–2.30.35 ...0.250.05 0.15
A242.0 A12420remainder0.60.83.7–4.5 0.101.2–1.70.15–0.251.8–2.30.10 ... 0.07–0.200.05 0.15
295.0 A02950remainder0.7–1.5 1.04.0–5.00.350.03......0.35 ...0.250.050.15
319.0 A03190remainder5.5–6.5 1.03.0–4.00.500.10...0.351.0 ...0.25...0.50
328.0 A03280remainder7.5–8.5 1.01.0–2.00.20–0.60.20–0.60.35 0.251.5...0.25...0.50
355.0 A03550remainder4.5–5.5 0.6B1.0–1.50.50B0.40–0.60.25... 0.35...0.25 0.050.15
C355.0 A33550remainder4.5–5.5 0.201.0–1.50.100.40–0.6... ...0.10...0.200.05 0.15
356.0 A03560remainder6.5–7.5 0.6B0.250.35B0.20–0.45...... 0.35...0.250.050.15
A356.0 A13560remainder6.5–7.5 0.200.20 0.100.25–0.45... ...0.10 ...0.200.05 0.15
443.0 A04430remainder4.5–6.0 0.80.6 0.500.050.25...0.50 ...0.25 ...0.35
B443.0 A24430remainder4.5–6.0 0.80.15 0.350.05......0.35 ...0.25 0.050.15
512.0 A05120remainder1.4–2.2 0.60.35 0.83.5–4.50.25 ...0.35...0.25 0.05 0.15
514.0 A05140remainder0.350.500.15 0.353.5–4.5......0.15...0.25 0.050.15
520.0 A05200remainder0.250.300.25 0.159.5–10.6......0.15 ...0.25 0.050.15
535.0 A05350remainder0.150.150.05 0.10–0.256.2–7.5... .........0.10–0.250.05C 0.15
705.0 A07050remainder0.200.80.20 0.40–0.61.4–1.80.20–0.40...2.7–3.3... 0.250.05 0.15
707.0 A07070remainder0.200.80.20 0.40–0.61.8–2.40.20–0.40...4.0–4.5... 0.250.05 0.15
710.0DA07100 remainder0.150.500.35–0.650.05 0.6–0.8......6.0–7.0... 0.250.050.15
712.0DA07120 remainder0.300.500.250.100.50–0.650.40–0.6...5.0–6.5... 0.15–0.250.050.20
713.0 A07130remainder0.251.10.40–1.0 0.60.20–0.500.35 0.157.0–8.0...0.250.10 0.25
771.0 A07710remainder0.150.150.10 0.100.8–1.00.06–0.20...6.5–7.5...0.10–0.200.05 0.15
850.0 A08500remainder0.70.70.7–1.3 0.100.10...0.7–1.3... 5.5–7.00.20...0.30
851.0DA08510 remainder2.0–3.00.70.7–1.30.10 0.10...0.30–0.7...5.5–7.00.20...0.30
852.0DA08520 remainder0.400.71.7–2.30.10 0.6–0.9...0.9–1.5...5.5–7.00.20...0.30

A Contains silver 0.40–1.0 %.

B If iron exceeds 0.45 %, manganese content shall not be less than one half of the iron content.

C Contains beryllium 0.003–0.007 %, boron 0.005 % max.

D 710.0 formerly A712.0, 712.0 formerly D712.0, 851.0 formerly A850.0, 852.0 formerly B850.0.
국제분류(ICS)코드
페이지수 14
Edition 12

이력정보

No. 표준번호 표준명 발행일 상태
1 ASTM B26/B26M-18e1상세보기 Standard Specification for Aluminum-Alloy Sand Castings 2018-05-15 표준
2 ASTM B26/B26M-18상세보기 Standard Specification for Aluminum-Alloy Sand Castings 2018-05-15 구판
3 ASTM B26/B26M-14상세보기 Standard Specification for Aluminum-Alloy Sand Castings 2014-10-01 구판
4 ASTM B26/B26M-14e1상세보기 Standard Specification for Aluminum-Alloy Sand Castings 2014-10-01 구판
5 ASTM B26/B26M-12상세보기 Standard Specification for Aluminum-Alloy Sand Castings 2012-05-01 구판
6 ASTM B26/B26M-11상세보기 Standard Specification for Aluminum-Alloy Sand Castings 2011-12-01 구판
7 ASTM B26/B26M-09상세보기 Standard Specification for Aluminum-Alloy Sand Castings 2009-05-01 구판
8 ASTM B26/B26M-05상세보기 Standard Specification for Aluminum-Alloy Sand Castings 2005-09-01 구판
9 ASTM B26/B26M-03상세보기 Standard Specification for Aluminum-Alloy Sand Castings 2003-04-10 구판
10 ASTM B26/B26M-02상세보기 Standard Specification for Aluminum-Alloy Sand Castings 2002-10-10 구판
11 ASTM B26/B26M-99상세보기 Standard Specification for Aluminum-Alloy Sand Castings 2001-04-10 구판
12 ASTM B26/B26M-01상세보기 Standard Specification for Aluminum-Alloy Sand Castings 2001-04-10 구판
13 ASTM B26/B26M-97상세보기 Standard Specification for Aluminum-Alloy Sand Castings 구판

관련상품

  • 관련상품이 존재하지 않습니다.

다른 사람이 함께 구입한 상품

  • 함께 구입한 상품이 존재하지 않습니다.

추천 상품

제공형태 닫기

  • PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)

  • 보안PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능

  • PRINT :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

  • BOOK :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

  • ZIP :

    압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)

  • CD/DVD :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)

  • DB :

    별도 정보 제공

  • HARDCOPY :

    해외 배송 상품, 최대 3주 소요

  • 바인더 :

    바인더 우편발송, 2~3일 소요

  • 온라인구독 :

    WEB 접속 후 실시간 열람, 출력(1년간)