한국표준정보망

회원가입 로그인 비회원(주문조회) 장바구니 이용안내

English
메뉴
검색 마이페이지 장바구니0

QUICK

닫기

TOP

해외표준 상세정보

관심표준 등록 : 표준업데이트 시 알림서비스

제공형태 더보기

  • KS

    구판

    판매

    ASTM D1140-14

    Standard Test Methods for Determining the Amount of Material Finer than 75-μm (No. 200) Sieve in Soils by Washing
    • 발행일 : 2014-11-01
    • 발행기관 : ASTM
    즐겨찾기 장바구니 담기
    닫기

    상품이 장바구니에 담겼습니다.

    장바구니로 이동

    • [영어]PDF 131,600원

    • [영어]PRINT 131,600원

상세정보

분야 04.08 : 토양, 석재 (Ⅰ)
적용범위

1.1 These test methods cover the determination of the amount of material finer than a 75-μm (No. 200) sieve by washing of material with a maximum particle size of 75 mm (3 in.).

1.2 The methods used in this standard rely on the use of water or a dispersant to separate and remove materials finer than a 75-μm (No. 200) sieve. During these processes soluble substances, such as salts and other minerals, may also be removed. It is not within the scope of this standard to differentiate between the removal of fine particles and soluble substances. It is recommended that materials containing significant amounts of soluble substances be tested using other methods of separation.

1.3 Two methods for determining the amount of material finer than the 75-μm (No. 200) sieve are provided. The method to be used shall be specified by the requesting authority. If no method is specified, the choice should be based upon the guidance given in 5.2, 5.3, and 5.4.

1.3.1 Method A—Test specimen is dispersed by soaking in water prior to wash sieving.

1.3.2 Method B—Test specimen is dispersed by soaking in a dispersing solution prior to wash sieving.

1.4 Units—The values stated in SI units are to be regarded as standard. Except the sieve designations are typically identified using the “alternative” system in accordance with Specification E11, such as 3 inch and No. 200, instead of the “standard” of 75-mm and 75-μm, respectively. Reporting of test results in units other than SI shall not be regarded as nonconformance with this test method. The use of balances or scales recording pounds of mass (lbm) shall not be regarded as nonconformance with this standard.

1.5 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026, unless superseded by this test method.

1.5.1 The procedures used to specify how data are collected/recorded and calculated in this standard are regarded as the industry standard. In addition, they are representative of the significant digits that generally should be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of these test methods to consider significant digits used in analysis methods for engineering design.

1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
국제분류(ICS)코드
페이지수 6
Edition 14

이력정보

No. 표준번호 표준명 발행일 상태
1 ASTM D1140-17 REDLINE상세보기 Standard Test Methods for Determining the Amount of Material Finer than 75-μm (No. 200) Sieve in Soils by Washing 2017-02-01 표준
2 ASTM D1140-17상세보기 Standard Test Methods for Determining the Amount of Material Finer than 75-μm (No. 200) Sieve in Soils by Washing 2017-02-01 표준
3 ASTM D1140-14상세보기 Standard Test Methods for Determining the Amount of Material Finer than 75-μm (No. 200) Sieve in Soils by Washing 2014-11-01 구판
4 ASTM D1140-00(2006)상세보기 Standard Test Methods for Amount of Material in Soils Finer than No. 200 (75-μm) Sieve 2006-11-15 구판
5 ASTM D1140-00상세보기 Standard Test Methods for Amount of Material in Soils Finer Than the No. 200 (75-um) Sieve 2000-06-10 구판

관련상품

  • 관련상품이 존재하지 않습니다.

다른 사람이 함께 구입한 상품

  • 함께 구입한 상품이 존재하지 않습니다.

추천 상품

제공형태 닫기

  • PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)

  • 보안PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능

  • PRINT :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

  • BOOK :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

  • ZIP :

    압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)

  • CD/DVD :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)

  • DB :

    별도 정보 제공

  • HARDCOPY :

    해외 배송 상품, 최대 3주 소요

  • 바인더 :

    바인더 우편발송, 2~3일 소요

  • 온라인구독 :

    WEB 접속 후 실시간 열람, 출력(1년간)