사업자등록증
해외표준
FAQ
장바구니
고객센터
해외표준 상세정보
관심표준 등록 : 표준업데이트 시 알림서비스
제공형태 더보기-
구판
판매
ASTM D4440-15
Standard Test Method for Plastics: Dynamic Mechanical Properties Melt Rheology- 발행일 : 2015-01-15
- 발행기관 : ASTM
상세정보
| 분야 | 08.02 : 플라스틱 (Ⅱ) |
|---|---|
| 적용범위 | 1.1 This test method outlines the use of dynamic mechanical instrumentation in determining and reporting the rheological properties of thermoplastic resins and other types of molten polymers. It may be used as a method for determining the complex viscosity and other significant viscoelastic characteristics of such materials as a function of frequency, strain amplitude, temperature, and time. Such properties may be influenced by fillers and other additives. 1.2 It incorporates a laboratory test method for determining the relevant rheological properties of a polymer melt subjected to various oscillatory deformations on an instrument of the type commonly referred to as a mechanical or dynamic spectrometer. 1.3 This test method is intended to provide a means of determining the rheological properties of molten polymers, such as thermoplastics and thermoplastic elastomers over a range of temperatures by nonresonant, forced-vibration techniques. Plots of modulus, viscosity, and tan delta as a function of dynamic oscillation (frequency), strain amplitude, temperature, and time are indicative of the viscoelastic properties of a molten polymer. 1.4 This test method is valid for a wide range of frequencies, typically from 0.01 to 100 Hz. 1.5 This test method is intended for homogenous and heterogeneous molten polymeric systems and composite formulations containing chemical additives, including fillers, reinforcements, stabilizers, plasticizers, flame retardants, impact modifiers, processing aids, and other important chemical additives often incorporated into a polymeric system for specific functional properties, and which could affect the processability and functional performance. These polymeric material systems have molten viscosities typically less than 106 Pa·s (107 poise). 1.6 Apparent discrepancies may arise in results obtained under differing experimental conditions. Without changing the observed data, reporting in full (as described in this test method) the conditions under which the data was obtained may enable apparent differences observed in another study to be reconciled. 1.7 Test data obtained by this test method are relevant and appropriate for use in engineering design. 1.8 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 1: This test method is equivalent to ISO 6721, Part 10. |
| 국제분류(ICS)코드 | 83.080.20 : 열가소성 수지재 |
| 페이지수 | 5 |
| Edition | 15 |
이력정보
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D4440-23상세보기 | Standard Test Method for Plastics: Dynamic Mechanical Properties Melt Rheology | 2023-10-01 | 표준 |
| 2 | ASTM D4440-23 REDLINE상세보기 | Standard Test Method for Plastics: Dynamic Mechanical Properties Melt Rheology | 2023-10-01 | 표준 |
| 3 | ASTM D4440-15 REDLINE상세보기 | Standard Test Method for Plastics: Dynamic Mechanical Properties Melt Rheology | 2015-01-15 | 구판 |
| 4 | ASTM D4440-15상세보기 | Standard Test Method for Plastics: Dynamic Mechanical Properties Melt Rheology | 2015-01-15 | 구판 |
| 5 | ASTM D4440-08상세보기 | Standard Test Method for Plastics: Dynamic Mechanical Properties Melt Rheology | 2008-08-01 | 구판 |
| 6 | ASTM D4440-07상세보기 | Standard Test Method for Plastics: Dynamic Mechanical Properties: Melt Rheology | 2007-03-01 | 구판 |
| 7 | ASTM D4440-95a상세보기 | Standard Test Method for Plastics: Dynamic Mechanical Properties: Melt Rheology | 2001-09-10 | 구판 |
| 8 | ASTM D4440-01상세보기 | Standard Test Method for Plastics: Dynamic Mechanical Properties: Melt Rheology | 2001-09-10 | 구판 |
관련상품
- 관련상품이 존재하지 않습니다.
다른 사람이 함께 구입한 상품
- ASTM D7271-06(2020) - Standard Test Method for Viscoelastic Properties of Paste Ink Vehicle Using an Oscillatory Rheometer
- ASTM D7026-13 - Standard Guide for Sampling and Reporting of Results for Determination of Biobased Content of Materials via Carbon Isotope Analysis (Withdrawn 2020)
- ISO 4049:2019 - Dentistry — Polymer-based restorative materials
- ISO 19403-3:2017 - Paints and varnishes — Wettability — Part 3: Determination of the surface tension of liquids using the pendant drop method
- ISO/TS 80004-6:2013 - Nanotechnologies — Vocabulary — Part 6: Nano-object characterization
추천 상품
- IEC TS 63134:2020 - Active assisted living (AAL) use cases
- IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification
- KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs)
- KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs)
- KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스
제공형태 닫기
PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)보안PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능PRINT :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)BOOK :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)ZIP :
압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)CD/DVD :
직접 파일 다운로드 및 인쇄(마이페이지 확인)DB :
별도 정보 제공HARDCOPY :
해외 배송 상품, 최대 3주 소요바인더 :
바인더 우편발송, 2~3일 소요온라인구독 :
WEB 접속 후 실시간 열람, 출력(1년간)