한국표준정보망

회원가입 로그인 비회원(주문조회) 장바구니 이용안내

English
메뉴
검색 마이페이지 장바구니0

QUICK

닫기

TOP

해외표준 상세정보

관심표준 등록 : 표준업데이트 시 알림서비스

제공형태 더보기

  • KS

    구판

    판매

    ASTM A709/A709M-16a

    Standard Specification for Structural Steel for Bridges
    • 발행일 : 2016-05-01
    • 발행기관 : ASTM
    즐겨찾기 장바구니 담기
    닫기

    상품이 장바구니에 담겼습니다.

    장바구니로 이동

    • [영어]PDF 132,600원

    • [영어]PRINT 132,600원

상세정보

분야 01.04 : 철강-구조물, 보강재, 압력용기, 철도
적용범위

1.1 This specification covers carbon and high-strength low-alloy steel structural shapes, plates, and bars and quenched and tempered alloy steel for structural plates intended for use in bridges. Seven grades are available in four yield strength levels as follows:

Grade U.S. [SI]

Yield Strength, ksi [MPa]

      36 [250]

 36 [250]    

      50 [345]

 50 [345]    

      50S [345S]

 50 [345]    

      50W [345W]

 50 [345]    

      HPS 50W [HPS 345W]

 50 [345]    

      HPS 70W [HPS 485W]

 70 [485]    

      HPS 100W [HPS 690W]

100 [690]    

1.1.1 Grades 36 [250], 50 [345], 50S [345S], and 50W [345W] are also included in Specifications A36/A36M, A572/A572M, A992/A992M, and A588/A588M, respectively. When the requirements of Table 9 or Table 10 or the supplementary requirements of this specification are specified, they exceed the requirements of Specifications A36/A36M, A572/A572M, A992/A992M, and A588/A588M.

1.1.2 Grades 50W [345W], HPS 50W [HPS 345W], HPS 70W [HPS 485W], and HPS 100W [HPS 690W] have enhanced atmospheric corrosion resistance (see 13.1.2). Product availability is shown in Table 1.

(A) See specimen orientation and preparation subsection in the Tension Tests section of Specification A6/A6M.
(B) Measured at 0.2 % offset or 0.5 % extension under load as described in Section 13 of Test Methods A370.
(C) Elongation and reduction of area not required to be determined for floor plates.
(D) For plates wider than 24 in. [600 mm], the reduction of area requirement, where applicable, is reduced by five percentage points.
(E) For plates wider than 24 in. [600 mm], the elongation requirement is reduced by two percentage points. See elongation requirement adjustments in the Tension Tests section of Specification A6/A6M.
(F) Elongation in 2 in. or 50 mm: 19 % for shapes with flange thickness over 3 in. [75 mm].
(G) Not applicable.
(H) The yield to tensile ratio shall be 0.87 or less for shapes that are tested from the web location; for all other shapes, the requirement is 0.85.
(I) A maximum yield strength of 70 ksi [480 MPa] is permitted for structural shapes that are required to be tested from the web location.
(J) For wide flange shapes with flange thickness over 3 in. [75 mm], elongation in 2 in. or 50 mm of 18 % minimum applies.
(K) If measured on the Fig. 3 (Test Methods A370) 11/2-in. [40–mm] wide specimen, the elongation is determined in a 2-in. or 50-mm gage length that includes the fracture and shows the greatest elongation.
(L) 40 % minimum applies if measured on the Fig 3 (Test Methods A370) 11/2-in. [40-mm] wide specimen; 50 % minimum applies if measured on the Fig. 4 (Test Methods A370) 1/2-in. [12.5-mm] round specimen.
(M) Not applicable to Fracture Critical Tension Components (see Table 10).
(A) Manganese content of 0.85 to 1.35 % and silicon content of 0.15 to 0.40 % is required for shapes with flange thickness over 3 in. [75 mm].
(B) For each reduction of 0.01 % below the specified carbon maximum, an increase of 0.06 % manganese above the specified maximum will be permitted up to a maximum of 1.35 %.
(A) Copper when specified shall have a minimum content of 0.20 % by heat analysis (0.18 % by product analysis).
(B) Manganese, minimum by heat analysis of 0.80 % (0.75 % by product analysis) shall be required for all plates over 3/8 in. [10 mm] in thickness; a minimum of 0.50 % (0.45 % by product analysis) shall be required for plates 3/8 in. [10 mm] and less in thickness, and for all other products. The manganese to carbon ratio shall not be less than 2 to 1. For each reduction of 0.01 percentage point below the specified carbon maximum, an increase of 0.06 percentage point manganese above the specified maximum is permitted, up to a maximum of 1.60 %.
(C) A maximum phosphorus content of 0.04 % and a maximum sulfur content of 0.05 % are permitted for the following materials:

· Structural shapes

· Bars

· Plates with widths up to and including 15 in. [380 mm]

(D) Silicon content in excess of 0.40 % by heat analysis must be negotiated.
(A) Alloy content shall be in accordance with Type 1, 2, 3, or 5 and the contents of the applicable elements shall be reported on the test report.
(B) Product analysis limits = 0.004 to 0.06 %.
(C) Product analysis limits = 0.005 to 0.17 %.
(D) Product analysis limits = 0.01 to 0.16 %.
(A) Weldability data for these types have been qualified by FHWA for use in bridge construction.
(B) For each reduction of 0.01 percentage point below the specified maximum for carbon, an increase of 0.06 percentage point above the specified maximum for manganese is permitted, up to a maximum of 1.50 %.
(C) A maximum phosphorus content of 0.04 % and a maximum sulfur content of 0.05 % are permitted for the following materials:

· Structural shapes

· Bars

· Plates with widths up to and including 15 in. [380 mm]

(A) The steel shall be calcium treated for sulfide shape control.
(A) Provided that the ratio of manganese to sulfur is not less than 20 to 1, the minimum limit for manganese for shapes with flange or leg thickness not exceeding 1 in. [25 mm] shall be 0.30 %.
(B) The sum of columbium and vanadium shall not exceed 0.15 %.

1.2 Grade HPS 70W [HPS 485W] or HPS 100W [HPS 690W] shall not be substituted for Grades 36 [250], 50 [345], 50S [345S], 50W [345W], or HPS 50W [HPS 345W]. Grade 50W [345W], or HPS 50W [HPS 345W] shall not be substituted for Grades 36 [250], 50 [345] or 50S [345S] without agreement between the purchaser and the supplier.

1.3 When the steel is to be welded, it is presupposed that a welding procedure suitable for the grade of steel and intended use or service will be utilized. See Appendix X3 of Specification A6/A6M for information on weldability.

1.4 For structural products to be used as tension components requiring notch toughness testing, standardized requirements are provided in this standard, and they are based upon American Association of State Highway and Transportation Officials (AASHTO) requirements for both fracture critical and non-fracture critical members.

1.5 Supplementary requirements are available but shall apply only if specified in the purchase order.

1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.7 For structural products produced from coil and furnished without heat treatment or with stress relieving only, the additional requirements, including additional testing requirements and the reporting of additional test results, of Specification A6/A6M apply.
국제분류(ICS)코드
페이지수 8
Edition 16a

이력정보

No. 표준번호 표준명 발행일 상태
1 ASTM A709/A709M-24상세보기 Standard Specification for Structural Steel for Bridges 2024-10-15 표준
2 ASTM A709/A709M-24 REDLINE상세보기 Standard Specification for Structural Steel for Bridges 2024-10-15 표준
3 ASTM A709/A709M-21상세보기 Standard Specification for Structural Steel for Bridges 2021-11-01 구판
4 ASTM A709/A709M-21 REDLINE상세보기 Standard Specification for Structural Steel for Bridges 2021-11-01 구판
5 ASTM A709/A709M-18상세보기 Standard Specification for Structural Steel for Bridges 2018-11-15 구판
6 ASTM A709/A709M-18 REDLINE상세보기 Standard Specification for Structural Steel for Bridges 2018-11-15 구판
7 ASTM A709/A709M-17상세보기 Standard Specification for Structural Steel for Bridges 2017-09-01 구판
8 ASTM A709/A709M-17e1상세보기 Standard Specification for Structural Steel for Bridges 2017-09-01 구판
9 ASTM A709/A709M-16a상세보기 Standard Specification for Structural Steel for Bridges 2016-05-01 구판
10 ASTM A709/A709M-16상세보기 Standard Specification for Structural Steel for Bridges 2016-02-15 구판
11 ASTM A709/A709M-15상세보기 Standard Specification for Structural Steel for Bridges 2015-09-01 구판
12 ASTM A709/A709M-13a상세보기 Standard Specification for Structural Steel for Bridges 2013-10-01 구판
13 ASTM A709/A709M-13상세보기 Standard Specification for Structural Steel for Bridges 2013-05-01 구판
14 ASTM A709/A709M-11상세보기 Standard Specification for Structural Steel for Bridges 2011-05-01 구판
15 ASTM A709/A709M-10상세보기 Standard Specification for Structural Steel for Bridges 2010-09-01 구판
16 ASTM A709/A709M-09a상세보기 Standard Specification for Structural Steel for Bridges 2009-10-01 구판
17 ASTM A709/A709M-09상세보기 Standard Specification for Structural Steel for Bridges 2009-04-01 구판
18 ASTM A709/A709M-08상세보기 Standard Specification for Structural Steel for Bridges 2008-10-01 구판
19 ASTM A709/A709M-07상세보기 Standard Specification for Structural Steel for Bridges 2007-03-01 구판
20 ASTM A709/A709M-06a상세보기 Standard Specification for Structural Steel for Bridges 2006-09-01 구판
21 ASTM A709/A709M-06상세보기 Standard Specification for Structural Steel for Bridges 2006-03-15 구판
22 ASTM A709/A709M-05상세보기 Standard Specification for Structural Steel for Bridges 2005-04-01 구판
23 ASTM A709/A709M-04ae1상세보기 Standard Specification for Carbon and High-Strength Low-Alloy Structural Steel Shapes, Plates, and Bars and Quenched-and-Tempered Alloy Structural Steel Plates for Bridges 2004-09-01 구판
24 ASTM A709/A709M-04a상세보기 Standard Specification for Carbon and High-Strength Low-Alloy Structural Steel Shapes, Plates, and Bars and Quenched-and-Tempered Alloy Structural Steel Plates for Bridges 2004-09-01 구판
25 ASTM A709/A709M-04상세보기 Standard Specification for Carbon and High-Strength Low-Alloy Structural Steel Shapes, Plates, and Bars and Quenched-and-Tempered Alloy Structural Steel Plates for Bridges 2004-04-01 구판
26 ASTM A709/A709M-03a상세보기 Standard Specification for Carbon and High-Strength Low-Alloy Structural Steel Shapes, Plates, and Bars and Quenched-and-Tempered Alloy Structural Steel Plates for Bridges 2003-05-10 구판
27 ASTM A709/A709M-03상세보기 Standard Specification for Carbon and High-Strength Low-Alloy Structural Steel Shapes, Plates, and Bars and Quenched-and-Tempered Alloy Structural Steel Plates for Bridges 2003-04-10 구판
28 ASTM A709/A709M-01be2상세보기 Standard Specification for Carbon and High-Strength Low-Alloy Structural Steel Shapes, Plates, and Bars and Quenched-and-Tempered Alloy Structural Steel Plates for Bridges 2001-10-10 구판
29 ASTM A709/A709M-01b상세보기 Standard Specification for Carbon and High-Strength Low-Alloy Structural Steel Shapes, Plates, and Bars and Quenched-and-Tempered Alloy Structural Steel Plates for Bridges 2001-10-10 구판
30 ASTM A709/A709M-01be1상세보기 Standard Specification for Carbon and High-Strength Low-Alloy Structural Steel Shapes, Plates, and Bars and Quenched-and-Tempered Alloy Structural Steel Plates for Bridges 2001-10-10 구판
31 ASTM A709/A709M-01a상세보기 Standard Specification for Carbon and High-Strength Low-Alloy Structural Steel Shapes, Plates, and Bars and Quenched-and-Tempered Alloy Structural Steel Plates for Bridges 2001-10-10 구판
32 ASTM A709/A709M-01상세보기 Standard Specification for Carbon and High-Strength Low-Alloy Structural Steel Shapes, Plates, and Bars and Quenched-and-Tempered Alloy Structural Steel Plates for Bridges 2001-10-10 구판
33 ASTM A709/A709M-00a상세보기 Standard Specification for Carbon and High-Strength Low-Alloy Structural Steel Shapes, Plates, and Bars and Quenched-and-Tempered Alloy Structural Steel Plates for Bridges 2001-10-10 구판
34 ASTM A709/A709M-01be3상세보기 Standard Specification for Carbon and High-Strength Low-Alloy Structural Steel Shapes, Plates, and Bars and Quenched-and-Tempered Alloy Structural Steel Plates for Bridges 2001-10-10 구판
35 ASTM A709/A709M-00상세보기 Standard Specification for Carbon and High-Strength Low-Alloy Structural Steel Shapes, Plates, and Bars and Quenched-and-Tempered Alloy Structural Steel Plates for Bridges 2001-10-10 구판

관련상품

  • 관련상품이 존재하지 않습니다.

다른 사람이 함께 구입한 상품

  • 함께 구입한 상품이 존재하지 않습니다.

추천 상품

제공형태 닫기

  • PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)

  • 보안PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능

  • PRINT :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

  • BOOK :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

  • ZIP :

    압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)

  • CD/DVD :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)

  • DB :

    별도 정보 제공

  • HARDCOPY :

    해외 배송 상품, 최대 3주 소요

  • 바인더 :

    바인더 우편발송, 2~3일 소요

  • 온라인구독 :

    WEB 접속 후 실시간 열람, 출력(1년간)