사업자등록증
해외표준
FAQ
장바구니
고객센터
해외표준 상세정보
관심표준 등록 : 표준업데이트 시 알림서비스
제공형태 더보기-
구판
판매
ASTM D4473-08(2016)
Standard Test Method for Plastics: Dynamic Mechanical Properties: Cure Behavior- 발행일 : 2016-11-01
- 발행기관 : ASTM
상세정보
| 분야 | 08.02 : 플라스틱 (Ⅱ) |
|---|---|
| 적용범위 | 1.1 This test method covers the use of dynamic-mechanical-oscillation instrumentation for gathering and reporting the thermal advancement of cure behavior of thermosetting resin. It may be used for determining the cure properties of both unsupported resins and resins supported on substrates subjected to various oscillatory deformations. 1.2 This test method is intended to provide a means for determining the cure behavior of supported and unsupported thermosetting resins over a range of temperatures by free vibration as well as resonant and nonresonant forced-vibration techniques, in accordance with Practice D4065. Plots of modulus, tan delta, and damping index as a function of time/temperature are indicative of the thermal advancement or cure characteristics of a resin. 1.3 This test method is valid for a wide range of frequencies, typically from 0.01 to 100 Hz. However, it is strongly recommended that low-frequency test conditions, generally below 1.5 Hz, be utilized as they generally will result in more definitive cure-behavior information. 1.4 This test method is intended for resin/substrate composites that have an uncured effective elastic modulus in shear greater than 0.5 MPa. 1.5 Apparent discrepancies may arise in results obtained under differing experimental conditions. These apparent differences from results observed in another study can usually be reconciled, without changing the observed data, by reporting in full (as described in this test method) the conditions under which the data were obtained. 1.6 Due to possible instrumentation compliance, especially in the compressive mode, the data generated may indicate relative and not necessarily absolute property values. 1.7 Test data obtained by this test method are relevant and appropriate for use in engineering design. 1.8 The values stated in SI units are to be regarded as the standard. 1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Note 5. Note 1: There is no known ISO equivalent to this standard. |
| 국제분류(ICS)코드 | 83.080.10 : 열경화재 |
| 페이지수 | 5 |
| Edition | 08(2016) |
이력정보
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D4473-08(2021)상세보기 | Standard Test Method for Plastics: Dynamic Mechanical Properties: Cure Behavior | 2021-07-01 | 표준 |
| 2 | ASTM D4473-08(2016)상세보기 | Standard Test Method for Plastics: Dynamic Mechanical Properties: Cure Behavior | 2016-11-01 | 구판 |
| 3 | ASTM D4473-08상세보기 | Standard Test Method for Plastics: Dynamic Mechanical Properties: Cure Behavior | 2008-03-01 | 구판 |
| 4 | ASTM D4473-03상세보기 | Standard Test Method for Plastics: Dynamic Mechanical Properties: Cure Behavior | 2003-07-10 | 구판 |
| 5 | ASTM D4473-95a상세보기 | Standard Test Method for Plastics: Dynamic Mechanical Properties: Cure Behavior | 2001-09-10 | 구판 |
| 6 | ASTM D4473-01상세보기 | Standard Test Method for Plastics: Dynamic Mechanical Properties: Cure Behavior | 2001-09-10 | 구판 |
관련상품
- 관련상품이 존재하지 않습니다.
다른 사람이 함께 구입한 상품
- ASTM D149-20 - Standard Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials at Commercial Power Frequencies
- ASTM D2240-15e1 - Standard Test Method for Rubber Property—Durometer Hardness
- ASTM D2196-18e1 - Standard Test Methods for Rheological Properties of Non-Newtonian Materials by Rotational Viscometer
- ASTM D150-18 - Standard Test Methods for AC Loss Characteristics and Permittivity (Dielectric Constant) of Solid Electrical Insulation
- ASTM D792-13 - Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
추천 상품
- IEC TS 63134:2020 - Active assisted living (AAL) use cases
- IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification
- KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs)
- KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs)
- KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스
제공형태 닫기
PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)보안PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능PRINT :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)BOOK :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)ZIP :
압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)CD/DVD :
직접 파일 다운로드 및 인쇄(마이페이지 확인)DB :
별도 정보 제공HARDCOPY :
해외 배송 상품, 최대 3주 소요바인더 :
바인더 우편발송, 2~3일 소요온라인구독 :
WEB 접속 후 실시간 열람, 출력(1년간)