사업자등록증
해외표준
FAQ
장바구니
고객센터
해외표준 상세정보
관심표준 등록 : 표준업데이트 시 알림서비스
제공형태 더보기-
구판
판매
ASTM E3086-17
Standard Practice for Creating Appliques for Use in Testing of Nonplanar Soft Body Armor Designed for Females- 발행일 : 2017-02-01
- 발행기관 : ASTM
상세정보
| 분야 | 15.08 : 감지측정, 진공청소기, 안전 시스템 |
|---|---|
| 적용범위 | 1.1 This practice specifies a procedure for creating appliques (that is, build-up of clay) for use behind nonplanar, soft body armor test items and affixing the appliques to the clay block. Note 1: This practice describes a single applique shape; additional shapes may be described in other standards. 1.2 The purpose of this practice is to specify critical parameters for creating appliques in order to improve consistency of the test setup between laboratories. Note 2: In the past, testing of nonplanar soft armor has been done either with an unspecified buildup of clay behind the test item or with the test item pressed flat against the clay block. 1.3 This practice is applicable only to nonplanar soft body armor designed for females. 1.4 This practice is not applicable to hard armor test items. 1.5 This practice is primarily directed toward test laboratories but may be applicable to body armor manufacturers, researchers, and end users performing ballistic-resistance testing of body armor. 1.6 In this practice, “other standards and specifications” and “unless specified elsewhere” refer to documents (for example, military standards, purchase specifications) that require the use of this practice. Purchasers and other users are responsible for the “other standards and specifications” and for specifying any requirements that supersede those of this practice. 1.7 Units—The values stated in SI units are to be regarded as standard. Where appropriate, inch-pound units are included parenthetically for information purposes. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
| 국제분류(ICS)코드 |
13.310 : 범죄로부터의 보호
13.340.01 : 보호장비 일반 |
| 페이지수 | 5 |
| Edition | 17 |
이력정보
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM E3086-20상세보기 | Standard Practice for Creating Appliques for Use in Testing of Nonplanar Soft Body Armor Designed for Females | 2020-04-01 | 표준 |
| 2 | ASTM E3086-20 REDLINE상세보기 | Standard Practice for Creating Appliques for Use in Testing of Nonplanar Soft Body Armor Designed for Females | 2020-04-01 | 표준 |
| 3 | ASTM E3086-17상세보기 | Standard Practice for Creating Appliques for Use in Testing of Nonplanar Soft Body Armor Designed for Females | 2017-02-01 | 구판 |
관련상품
- 관련상품이 존재하지 않습니다.
다른 사람이 함께 구입한 상품
- ASTM E3004-15e1 - Standard Specification for Preparation and Verification of Clay Blocks Used in Ballistic-Resistance Testing of Torso Body Armor
- ASTM E3062-16e1 - Standard Specification for Indoor Ballistic Test Ranges for Small Arms and Fragmentation Testing of Ballistic-resistant Items
- ASTM E3005-15 - Standard Terminology for Body Armor
- ASTM E3068-17 - Standard Test Method for Contact Measurement of Backface Deformation in Clay Backing During Body Armor Testing
- ASTM E3107-17a - Standard Test Method for Resistance to Penetration and Backface Deformation for Ballistic-resistant Torso Body Armor and Shoot Packs
추천 상품
- IEC TS 63134:2020 - Active assisted living (AAL) use cases
- IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification
- KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs)
- KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs)
- KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스
제공형태 닫기
PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)보안PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능PRINT :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)BOOK :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)ZIP :
압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)CD/DVD :
직접 파일 다운로드 및 인쇄(마이페이지 확인)DB :
별도 정보 제공HARDCOPY :
해외 배송 상품, 최대 3주 소요바인더 :
바인더 우편발송, 2~3일 소요온라인구독 :
WEB 접속 후 실시간 열람, 출력(1년간)