해외표준 상세정보
관심표준 등록 : 표준업데이트 시 알림서비스
제공형태 더보기-
구판
판매
ASTM E228-17
Standard Test Method for Linear Thermal Expansion of Solid Materials With a Push-Rod Dilatometer- 발행일 : 2017-04-01
- 발행기관 : ASTM
상세정보
분야 | 14.01 : 보건정보학 |
---|---|
적용범위 | 1.1 This test method covers the determination of the linear thermal expansion of rigid solid materials using push-rod dilatometers. This method is applicable over any practical temperature range where a device can be constructed to satisfy the performance requirements set forth in this standard. Note 1: Initially, this method was developed for vitreous silica dilatometers operating over a temperature range of –180°C to 900°C. The concepts and principles have been amply documented in the literature to be equally applicable for operating at higher temperatures. The precision and bias of these systems is believed to be of the same order as that for silica systems up to 900°C. However, their precision and bias have not yet been established over the relevant total range of temperature due to the lack of well-characterized reference materials and the need for interlaboratory comparisons. 1.2 For this purpose, a rigid solid is defined as a material that, at test temperature and under the stresses imposed by instrumentation, has a negligible creep or elastic strain rate, or both, thus insignificantly affecting the precision of thermal-length change measurements. This includes, as examples, metals, ceramics, refractories, glasses, rocks and minerals, graphites, plastics, cements, cured mortars, woods, and a variety of composites. 1.3 The precision of this comparative test method is higher than that of other push-rod dilatometry techniques (for example, Test Method D696) and thermomechanical analysis (for example, Test Method E831) but is significantly lower than that of absolute methods such as interferometry (for example, Test Method E289). It is generally applicable to materials having absolute linear expansion coefficients exceeding 0.5 μm/(m·°C) for a 1000°C range, and under special circumstances can be used for lower expansion materials when special precautions are used to ensure that the produced expansion of the specimen falls within the capabilities of the measuring system. In such cases, a sufficiently long specimen was found to meet the specification. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
국제분류(ICS)코드 | 77.040.99 : 기타 금속 시험 방법 |
페이지수 | 10 |
Edition | 17 |
이력정보
No. | 표준번호 | 표준명 | 발행일 | 상태 |
---|---|---|---|---|
1 | ASTM E228-22상세보기 | Standard Test Method for Linear Thermal Expansion of Solid Materials With a Push-Rod Dilatometer | 2022-12-01 | 표준 |
2 | ASTM E228-22 REDLINE상세보기 | Standard Test Method for Linear Thermal Expansion of Solid Materials With a Push-Rod Dilatometer | 2022-12-01 | 표준 |
3 | ASTM E228-17상세보기 | Standard Test Method for Linear Thermal Expansion of Solid Materials With a Push-Rod Dilatometer | 2017-04-01 | 구판 |
4 | ASTM E228-17 REDLINE상세보기 | Standard Test Method for Linear Thermal Expansion of Solid Materials With a Push-Rod Dilatometer | 2017-04-01 | 구판 |
5 | ASTM E228-11(2016)상세보기 | Standard Test Method for Linear Thermal Expansion of Solid Materials With a Push-Rod Dilatometer | 2016-09-01 | 구판 |
6 | ASTM E228-11상세보기 | Standard Test Method for Linear Thermal Expansion of Solid Materials With a Push-Rod Dilatometer | 2011-04-01 | 구판 |
7 | ASTM E228-06상세보기 | Standard Test Method for Linear Thermal Expansion of Solid Materials With a Push-Rod Dilatometer | 2006-09-01 | 구판 |
8 | ASTM E228-95상세보기 | Standard Test Method for Linear Thermal Expansion of Solid Materials With a Vitreous Silica Dilatometer (Withdrawn 2005) | 1995-01-01 | 구판 |
관련상품
- 관련상품이 존재하지 않습니다.
다른 사람이 함께 구입한 상품
- ASTM C177-19 - Standard Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus
- ISO 1922:2018 - Rigid cellular plastics — Determination of shear properties
- ASTM E96/E96M-16 - Standard Test Methods for Water Vapor Transmission of Materials
- ASTM D4986-20 - Standard Test Method for Horizontal Burning Characteristics of Cellular Polymeric Materials
- ISO 1926:2009 - Rigid cellular plastics — Determination of tensile properties
추천 상품
- IEC TS 63134:2020 - Active assisted living (AAL) use cases
- IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification
- KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs)
- KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs)
- KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스
제공형태 닫기
PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)보안PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능PRINT :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)BOOK :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)ZIP :
압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)CD/DVD :
직접 파일 다운로드 및 인쇄(마이페이지 확인)DB :
별도 정보 제공HARDCOPY :
해외 배송 상품, 최대 3주 소요바인더 :
바인더 우편발송, 2~3일 소요온라인구독 :
WEB 접속 후 실시간 열람, 출력(1년간)