한국표준정보망

회원가입 로그인 비회원(주문조회) 장바구니 이용안내

English
메뉴
검색 마이페이지 장바구니0

QUICK

닫기

TOP

해외표준 상세정보

관심표준 등록 : 표준업데이트 시 알림서비스

제공형태 더보기

  • KS

    구판

    판매

    ASTM D217-17

    Standard Test Methods for Cone Penetration of Lubricating Grease
    • 발행일 : 2017-05-01
    • 발행기관 : ASTM
    즐겨찾기 장바구니 담기
    닫기

    상품이 장바구니에 담겼습니다.

    장바구니로 이동

    • [영어]PDF 144,200원

    • [영어]PRINT 144,200원

상세정보

분야 05.01 : 석유제품 및 윤활유 (Ⅰ)
적용범위

1.1 These test methods cover four procedures for measuring the consistency of lubricating greases by the penetration of a cone of specified dimensions, mass, and finish. The penetration is measured in tenths of a millimetre.

Note 1: The National Lubricating Grease Institute (NLGI)2 classified greases according to their consistency as measured by the worked penetration. The classification system is as follows:

NLGI
Consistency Number

Worked Penetration Range,
25 °C (77 °F)

000

445 to 475

 00

400 to 430

  0

355 to 385

  1

310 to 340

  2

265 to 295

  3

220 to 250

  4

175 to 205

  5

130 to 160

  6

 85 to 115

1.1.1 The procedures for unworked, worked, and prolonged worked penetration are applicable to greases having penetrations between 85 and 475, that is, to greases with consistency numbers between NLGI 6 and NLGI 000. An undisturbed penetration test, described in Appendix X1, is similar to the unworked penetration test.

1.1.2 The block penetration procedure is applicable to greases that are sufficiently hard to hold their shape. Such greases usually have penetrations below eighty-five tenths of a millimetre.

1.1.3 Unworked penetrations do not generally represent the consistency of greases in use as effectively as do worked penetrations. The latter are usually preferred for inspecting lubricating greases.

1.2 None of the four procedures is considered suitable for the measurement of the consistency of petrolatums by penetration. Test Method D937 should be used for such products.

1.3 The dimensions of the equipment described in these test methods are given in SI units as the primary unit of measure with equivalent imperial units as accetpable alternatives where applicable. In cases where equivalent SI conversions are not known, notes are added for clarification. Temperatures and other dimensions are given in the preferred SI units; the values shown in parentheses are provided for information.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
국제분류(ICS)코드 75.100 : 윤활유
페이지수 14
Edition 17

이력정보

No. 표준번호 표준명 발행일 상태
1 ASTM D217-21a상세보기 Standard Test Methods for Cone Penetration of Lubricating Grease 2021-12-01 표준
2 ASTM D217-21a REDLINE상세보기 Standard Test Methods for Cone Penetration of Lubricating Grease 2021-12-01 표준
3 ASTM D217-21상세보기 Standard Test Methods for Cone Penetration of Lubricating Grease 2021-07-01 구판
4 ASTM D217-21 REDLINE상세보기 Standard Test Methods for Cone Penetration of Lubricating Grease 2021-07-01 구판
5 ASTM D217-19b상세보기 Standard Test Methods for Cone Penetration of Lubricating Grease 2019-11-01 구판
6 ASTM D217-19b REDLINE상세보기 Standard Test Methods for Cone Penetration of Lubricating Grease 2019-11-01 구판
7 ASTM D217-19a상세보기 Standard Test Methods for Cone Penetration of Lubricating Grease 2019-07-01 구판
8 ASTM D217-19a REDLINE상세보기 Standard Test Methods for Cone Penetration of Lubricating Grease 2019-07-01 구판
9 ASTM D217-19상세보기 Standard Test Methods for Cone Penetration of Lubricating Grease 2019-05-01 구판
10 ASTM D217-17상세보기 Standard Test Methods for Cone Penetration of Lubricating Grease 2017-05-01 구판
11 ASTM D217-17 REDLINE상세보기 Standard Test Methods for Cone Penetration of Lubricating Grease 2017-05-01 구판
12 ASTM D217-16상세보기 Standard Test Methods for Cone Penetration of Lubricating Grease 2016-10-01 구판
13 ASTM D217-10상세보기 Standard Test Methods for Cone Penetration of Lubricating Grease 2010-05-01 구판
14 ASTM D217-02(2007)상세보기 Standard Test Methods for Cone Penetration of Lubricating Grease 2007-11-01 구판
15 ASTM D217-02상세보기 Standard Test Methods for Cone Penetration of Lubricating Grease 2002-12-10 구판
16 ASTM D217-97상세보기 Standard Test Methods for Cone Penetration of Lubricating Grease 1997-11-10 구판

관련상품

  • 관련상품이 존재하지 않습니다.

다른 사람이 함께 구입한 상품

추천 상품

제공형태 닫기

  • PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)

  • 보안PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능

  • PRINT :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

  • BOOK :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

  • ZIP :

    압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)

  • CD/DVD :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)

  • DB :

    별도 정보 제공

  • HARDCOPY :

    해외 배송 상품, 최대 3주 소요

  • 바인더 :

    바인더 우편발송, 2~3일 소요

  • 온라인구독 :

    WEB 접속 후 실시간 열람, 출력(1년간)