한국표준정보망

회원가입 로그인 비회원(주문조회) 장바구니0 이용안내

English

메뉴

한국표준정보망전체메뉴

세계 주요 표준,
빠르고 편리하게!

ENGLISH

검색 마이페이지 장바구니0

QUICK

닫기

TOP

해외표준 상세정보

관심표준 등록 : 표준업데이트 시 알림서비스

제공형태 더보기

구판

판매

ASTM D1000-17

Standard Test Methods for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications
- 발행일 : 2017-07-01
- 발행기관 : ASTM
즐겨찾기 장바구니 담기

상품이 장바구니에 담겼습니다.
장바구니로 이동
- [영어]PDF 144,300원
- [영어]PRINT 144,300원

상세정보

분야

10.01 : 전기절연 (Ⅰ)

적용범위

1.1 These test methods cover procedures for testing pressure-sensitive adhesive-coated tapes to be used as electrical insulation. These tapes are classified as follows:

1.1.1 Class 1—Non-elastomeric backings made from materials such as:

	Paper, flat or creped,
	Fabric, uncoated or coated,
	Cellulose ester films,
	Polyethylene terephthalate (polyester) films,
	Fluorocarbon polymer films,
	Composite filament films,
	Polyamide films,
	Polyimide films, and
	Combinations thereof.

1.1.2 Class 2—Elastomeric backings that are characterized by both high stretch and substantial recovery. These backings are made from materials such as:

	Vinyl chloride and co-polymers,
	Vinylidene chloride and co-polymers, and
	Polyethylene and co-polymers.

1.2 Test laminates of Class 1 and Class 2 backings according to Class 1 test methods.

1.3 The procedures appear in the sections indicated below and in alphabetical order:

Adhesion Strength to Steel and Backing at Room Temperature	46 – 53
Adhesion Strength to Steel and Backing at Low Temperatures	46 – 53
Bond Strength After Solvent Immersion	110 – 115
Breaking Strength and Elongation at Room Temperature	37 – 45
Breaking Strength and Elongation at Low Temperatures	37 – 45
Conditioning	6 – 8
Curling and Twisting	140 – 146
Dielectric Breakdown Voltage	83 – 90
Effect of Accelerated Aging on High-Temperature Tapes	97 – 103
Flagging	66 – 76
Flammability	104 – 109
Hazards/Precautions	3
Insulation Resistance at High Humidity	91 – 96
Length of Tape in a Roll	28 – 36
Oil Resistance	116 – 122
Puncture Resistance	123 – 128
Resistance to Accelerated Aging (Heat and Moisture)	129 – 139
Sampling	4
Specimen Preparation	5
Thermosetting Properties	77 – 82
Thickness	21 – 27
Unwind Force at Room Temperature	54 – 65
Unwind Force at Low Temperatures	54 – 65
Width	11 – 20

Note 1: These procedures apply to both Class 1 and Class 2 tapes except as noted above.

1.4 This is a fire-test response standard (see Section 104).

1.5 The values stated in SI units are the standard, unless otherwise noted. If a value for measurement is followed by a value in inch-pound or English units in parentheses, it is likely that the second value will only be approximate and it is for information only. The first stated value is the preferred unit.

Note 2: These test methods are similar to IEC 60454–3, but may differ sometimes in some details.

1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazards see Section 3.

1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

국제분류(ICS)코드

29.035.20 : 유리 및 세라믹 절연 재료

페이지수

Edition

이력정보

No.	표준번호	표준명	발행일	상태
1	ASTM D1000-24상세보기	Standard Test Methods for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications	2024-09-01	표준
2	ASTM D1000-24 REDLINE상세보기	Standard Test Methods for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications	2024-09-01	표준
3	ASTM D1000-17 REDLINE상세보기	Standard Test Methods for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications	2017-07-01	구판
4	ASTM D1000-17상세보기	Standard Test Methods for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications	2017-07-01	구판
5	ASTM D1000-10상세보기	Standard Test Methods for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications	2010-01-01	구판
6	ASTM D1000-09상세보기	Standard Test Methods for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications	2009-10-15	구판
7	ASTM D1000-04e1상세보기	Standard Test Methods for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications	2004-09-01	구판
8	ASTM D1000-04상세보기	Standard Test Methods for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications	2004-09-01	구판
9	ASTM D1000-99상세보기	Standard Test Method for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications	1999-03-10	구판