한국표준정보망

회원가입 로그인 비회원(주문조회) 장바구니0 이용안내

English

메뉴

한국표준정보망전체메뉴

세계 주요 표준,
빠르고 편리하게!

ENGLISH

검색 마이페이지 장바구니0

QUICK

닫기

TOP

해외표준 상세정보

관심표준 등록 : 표준업데이트 시 알림서비스

제공형태 더보기

구판

판매

ASTM D6210-17

Standard Specification for Fully-Formulated Glycol Base Engine Coolant for Heavy-Duty Engines
- 발행일 : 2017-11-01
- 발행기관 : ASTM
즐겨찾기 장바구니 담기

상품이 장바구니에 담겼습니다.
장바구니로 이동
- [영어]보안PDF 118,100원

상세정보

분야

15.05 : 엔진냉각제; 할로겐유리솔벤트, 산업용화학제품

적용범위

1.1 This specification covers the requirements for fully-formulated glycol base coolants for cooling systems of heavy-duty engines. When concentrates are used at 40 to 60 % glycol concentration by volume in water of suitable quality, (see Appendix X1), or when prediluted glycol base engine coolants (50 volume % minimum) are used without further dilution, they will function effectively during both winter and summer to provide protection against corrosion, cavitation, freezing, and boiling.

1.2 This specification is intended to cover the requirements for engine coolants prepared from virgin or recycled ethylene or propylene glycol.

Note 1: Committee D15 has not substantially studied the impact of using recycled glycols from sources such as:

• glycol bottoms

• polyester manufacturing waste

• aircraft and runway deicers

• medical waste

to prepare engine coolants. However, several serious cases of very poor performance have been reported and substantiated in heavy duty fleets when recycled glycols from sources such as above have been used to prepare engine coolants. Efforts are underway to more clearly define the purity requirements for glycols used to prepare engine coolants meeting this specification, whether from recycled engine coolants or other sources.

1.3 The coolants governed by this specification are categorized as follows:

Coolant Type	Description

I-FF	Ethylene glycol base concentrate
II-FF	Propylene glycol base concentrate
III-FF	Ethylene glycol predilute (50 vol %)
IV-FF	Propylene glycol predilute (50 vol %)

1.4 Coolant concentrates meeting this specification do not require any addition of Supplemental Coolant Additive (SCA) until the first maintenance interval when a maintenance dose of SCA is required to continue protection in certain heavy duty engine cooling systems, particularly those of the wet cylinder liner-in-block design. The SCA additions are defined by and are the primary responsibility of the engine manufacturer or vehicle manufacturer. If they provide no instructions, follow the SCA supplier's instructions.

1.5 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.

1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

국제분류(ICS)코드

71.100.45 : 냉각제 및 부동액

페이지수

Edition

이력정보

No.	표준번호	표준명	발행일	상태
1	ASTM D6210-25상세보기	Standard Specification for Fully-Formulated Glycol Base Engine Coolant for Heavy-Duty Engines	2025-10-01	표준
2	ASTM D6210-17상세보기	Standard Specification for Fully-Formulated Glycol Base Engine Coolant for Heavy-Duty Engines	2017-11-01	구판
3	ASTM D6210-10상세보기	Standard Specification for Fully-Formulated Glycol Base Engine Coolant for Heavy-Duty Engines	2010-12-01	구판
4	ASTM D6210-08상세보기	Standard Specification for Fully-Formulated Glycol Base Engine Coolant for Heavy-Duty Engines	2008-10-01	구판
5	ASTM D6210-06상세보기	Standard Specification for Fully-Formulated Glycol Base Engine Coolant for Heavy-Duty Engines	2006-08-01	구판
6	ASTM D6210-04상세보기	Standard Specification for Fully-Formulated Glycol Base Engine Coolant for Heavy-Duty Engines	2004-10-01	구판
7	ASTM D6210-03e1상세보기	Standard Specification for Fully-Formulated Glycol Base Engine Coolant for Heavy-Duty Engines	2003-05-10	구판
8	ASTM D6210-03상세보기	Standard Specification for Fully-Formulated Glycol Base Engine Coolant for Heavy-Duty Engines	2003-05-10	구판
9	ASTM D6210-98a상세보기	Standard Specification for Fully-Formulated Ethylene-Glycol-Base Engine Coolant for Heavy-Duty Engines	1998-04-10	구판