관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
분야 | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
적용범위 | 1.1 These test methods2 cover procedures and definitions for the mechanical testing of steels, stainless steels, and related alloys. The various mechanical tests herein described are used to determine properties required in the product specifications. Variations in testing methods are to be avoided, and standard methods of testing are to be followed to obtain reproducible and comparable results. In those cases in which the testing requirements for certain products are unique or at variance with these general procedures, the product specification testing requirements shall control. 1.2 The following mechanical tests are described:
1.3 Annexes covering details peculiar to certain products are appended to these test methods as follows:
1.4 The values stated in inch-pound units are to be regarded as the standard. 1.5 When this document is referenced in a metric product specification, the yield and tensile values may be determined in inch-pound (ksi) units then converted into SI (MPa) units. The elongation determined in inch-pound gauge lengths of 2 or 8 in. may be reported in SI unit gauge lengths of 50 or 200 mm, respectively, as applicable. Conversely, when this document is referenced in an inch-pound product specification, the yield and tensile values may be determined in SI units then converted into inch-pound units. The elongation determined in SI unit gauge lengths of 50 or 200 mm may be reported in inch-pound gauge lengths of 2 or 8 in., respectively, as applicable. 1.5.1 The specimen used to determine the original units must conform to the applicable tolerances of the original unit system given in the dimension table not that of the converted tolerance dimensions. Note 1: This is due to the specimen SI dimensions and tolerances being hard conversions when this is not a dual standard. The user is directed to Test Methods A1058 if the tests are required in SI units. 1.6 Attention is directed to ISO/IEC 17025 when there may be a need for information on criteria for evaluation of testing laboratories. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||||||||||||||||||
국제분류(ICS)코드 | |||||||||||||||||||||||||||||||||||||||||
페이지수 | 50 | ||||||||||||||||||||||||||||||||||||||||
Edition | 17a |
No. | 표준번호 | 표준명 | 발행일 | 상태 |
---|---|---|---|---|
1 | ASTM A370-24 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products | 2024-03-01 | 표준 |
2 | ASTM A370-24 REDLINE | Standard Test Methods and Definitions for Mechanical Testing of Steel Products | 2024-03-01 | 표준 |
3 | ASTM A370-23 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products | 2023-09-15 | 구판 |
4 | ASTM A370-23 REDLINE | Standard Test Methods and Definitions for Mechanical Testing of Steel Products | 2023-09-15 | 구판 |
5 | ASTM A370-22 REDLINE | Standard Test Methods and Definitions for Mechanical Testing of Steel Products | 2022-10-01 | 구판 |
6 | ASTM A370-22 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products | 2022-10-01 | 구판 |
7 | ASTM A370-21 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products | 2021-11-01 | 구판 |
8 | ASTM A370-21 REDLINE | Standard Test Methods and Definitions for Mechanical Testing of Steel Products | 2021-11-01 | 구판 |
9 | ASTM A370-20 REDLINE | Standard Test Methods and Definitions for Mechanical Testing of Steel Products | 2020-08-01 | 구판 |
10 | ASTM A370-20 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products | 2020-08-01 | 구판 |
11 | ASTM A370-19 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products | 2019-07-01 | 구판 |
12 | ASTM A370-19e1 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products | 2019-07-01 | 구판 |
13 | ASTM A370-18 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products | 2018-12-01 | 구판 |
14 | ASTM A370-17a | Standard Test Methods and Definitions for Mechanical Testing of Steel Products | 2017-11-15 | 구판 |
15 | ASTM A370-17a REDLINE | Standard Test Methods and Definitions for Mechanical Testing of Steel Products | 2017-11-15 | 표준 |
16 | ASTM A370-17 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products | 2017-01-01 | 구판 |
17 | ASTM A370-16 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products | 2016-05-01 | 구판 |
18 | ASTM A370-15 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products | 2015-11-01 | 구판 |
19 | ASTM A370-14 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products | 2014-05-15 | 구판 |
20 | CSA A370:14 (R2023) | Connectors for masonry | 2014-01-01 | 표준 |
21 | ASTM A370-13 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products | 2013-11-15 | 구판 |
22 | ASTM A370-12a | Standard Test Methods and Definitions for Mechanical Testing of Steel Products | 2012-10-15 | 구판 |
23 | ASTM A370-12 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products | 2012-03-15 | 구판 |
24 | ASTM A370-11a | Standard Test Methods and Definitions for Mechanical Testing of Steel Products | 2011-11-15 | 구판 |
25 | ASTM A370-11 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products | 2011-05-01 | 구판 |
26 | ASTM A370-10 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products | 2010-06-15 | 구판 |
27 | ASTM A370-09ae1 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products | 2009-06-01 | 구판 |
28 | ASTM A370-09a | Standard Test Methods and Definitions for Mechanical Testing of Steel Products | 2009-06-01 | 구판 |
29 | ASTM A370-09 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products | 2009-01-01 | 구판 |
30 | ASTM A370-08b | Standard Test Methods and Definitions for Mechanical Testing of Steel Products | 2008-10-15 | 구판 |
31 | ASTM A370-08a | Standard Test Methods and Definitions for Mechanical Testing of Steel Products | 2008-04-14 | 구판 |
32 | ASTM A370-08 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products | 2008-04-01 | 구판 |
33 | ASTM A370-07b | Standard Test Methods and Definitions for Mechanical Testing of Steel Products | 2007-11-01 | 구판 |
34 | ASTM A370-07a | Standard Test Methods and Definitions for Mechanical Testing of Steel Products | 2007-06-01 | 구판 |
35 | ASTM A370-07 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products | 2007-04-01 | 구판 |
36 | ASTM A370-06 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products | 2006-11-01 | 구판 |
37 | ASTM A370-05 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products | 2005-05-01 | 구판 |
38 | ASTM A370-03 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products | 2003-06-10 | 구판 |
39 | ASTM A370-03a | Standard Test Methods and Definitions for Mechanical Testing of Steel Products | 2003-06-10 | 구판 |
40 | ASTM A370-02e1 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products | 2002-01-10 | 구판 |
41 | ASTM A370-02 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products | 2001-12-10 | 구판 |
42 | ASTM A370-01 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products | 2001-12-10 | 구판 |
43 | ASTM A370-97a | Standard Test Methods and Definitions for Mechanical Testing of Steel Products | 2001-12-10 | 구판 |
44 | ASTM A370-94 | Standard Test Methods and Definitions for Mechanical Testing of Steel Products | 구판 | |
45 | ASTM A370-68 | Standard Methods And Definitions For Mechanical Testing Of Steel Products | 구판 |
관련상품이 존재하지 않습니다.
ASTM E709-15 - Standard Guide for Magnetic Particle Testing 상세보기
ASTM A307-14e1 - Standard Specification for Carbon Steel Bolts, Studs, and Threaded Rod 60 000 PSI Tensile Strength 상세보기
ASTM A453/A453M-17 - Standard Specification for High-Temperature Bolting, with Expansion Coefficients Comparable to Austenitic Stainless Steels 상세보기
ASTM A193/A193M-17 - Standard Specification for Alloy-Steel and Stainless Steel Bolting for High Temperature or High Pressure Service and Other Special Purpose Applications 상세보기
ASTM A320/A320M-18 - Standard Specification for Alloy-Steel and Stainless Steel Bolting for Low-Temperature Service 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기