사업자등록증
해외표준
FAQ
장바구니
고객센터
해외표준 상세정보
관심표준 등록 : 표준업데이트 시 알림서비스
제공형태 더보기-
표준
판매
ASTM F2028-17
Standard Test Methods for Dynamic Evaluation of Glenoid Loosening or Disassociation- 발행일 : 2017-12-01
- 발행기관 : ASTM
상세정보
| 분야 | 13.01 : 의료기, 외과용 도구 및 장비 |
|---|---|
| 적용범위 | 1.1 These test methods measure how much a prosthetic anatomic glenoid component rocks or pivots following cyclic displacement of the humeral head to opposing glenoid rims (for example, superior-inferior or anterior-posterior). Motion is quantified by the tensile displacement opposite each loaded rim after dynamic rocking. Similarly, these test methods measure how much a prosthetic reverse glenoid component rocks or pivots following cyclic articulation with a mating humeral liner. Motion is quantified by the magnitude of displacement measured before and after cyclic loading. 1.2 The same setup can be used to test the locking mechanisms of modular glenoid components, for example, disassociation of both anatomic and reverse shoulder components. 1.3 These test methods cover shoulder replacement designs with monolithic or modular glenoid components for cemented fixation as well as reverse glenoid components for uncemented fixation. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | |
| 페이지수 | 15 |
| Edition | 17 |
이력정보
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM F2028-17 REDLINE상세보기 | Standard Test Methods for Dynamic Evaluation of Glenoid Loosening or Disassociation | 2017-12-01 | 표준 |
| 2 | ASTM F2028-17상세보기 | Standard Test Methods for Dynamic Evaluation of Glenoid Loosening or Disassociation | 2017-12-01 | 표준 |
| 3 | ASTM F2028-14상세보기 | Standard Test Methods for Dynamic Evaluation of Glenoid Loosening or Disassociation | 2014-03-01 | 구판 |
| 4 | ASTM F2028-08(2012)e1상세보기 | Standard Test Methods for Dynamic Evaluation of Glenoid Loosening or Disassociation | 2012-12-15 | 구판 |
| 5 | ASTM F2028-08상세보기 | Standard Test Methods for Dynamic Evaluation of Glenoid Loosening or Disassociation | 2008-02-01 | 구판 |
| 6 | ASTM F2028-05상세보기 | Standard Test Methods for Dynamic Evaluation of Glenoid Loosening or Disassociation | 2005-08-01 | 구판 |
| 7 | ASTM F2028-02상세보기 | Standard Test Methods for the Dynamic Evaluation of Glenoid Loosening or Disassociation | 2002-11-10 | 구판 |
| 8 | ASTM F2028-00e01상세보기 | Standard Test Methods for the Dynamic Evaluation of Glenoid Loosening or Disassociation | 2000-05-10 | 구판 |
| 9 | ASTM F2028-00상세보기 | Standard Test Methods for the Dynamic Evaluation of Glenoid Loosening or Disassociation | 2000-05-10 | 구판 |
관련상품
- 관련상품이 존재하지 않습니다.
다른 사람이 함께 구입한 상품
- KS P ISO 12865 - 안과용 기구 — 검영기
- ISO 80601-2-55:2018 - Medical electrical equipment — Part 2-55: Particular requirements for the basic safety and essential performance of respiratory gas monitors
- ISO 8537:2016 - Sterile single-use syringes, with or without needle, for insulin
- IEC 60601-2-3:2012+AMD1:2016+AMD2:2022 CSV - Medical electrical equipment - Part 2-3: Particular requirements for the basic safety and essential performance of short-wave therapy equipment
- ASTM F3210-22e1 - Standard Test Method for Fatigue Testing of Total Knee Femoral Components Under Closing Conditions
추천 상품
- IEC TS 63134:2020 - Active assisted living (AAL) use cases
- IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification
- KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs)
- KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs)
- KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스
제공형태 닫기
PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)보안PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능PRINT :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)BOOK :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)ZIP :
압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)CD/DVD :
직접 파일 다운로드 및 인쇄(마이페이지 확인)DB :
별도 정보 제공HARDCOPY :
해외 배송 상품, 최대 3주 소요바인더 :
바인더 우편발송, 2~3일 소요온라인구독 :
WEB 접속 후 실시간 열람, 출력(1년간)