사업자등록증
해외표준
FAQ
장바구니
고객센터
해외표준 상세정보
관심표준 등록 : 표준업데이트 시 알림서비스
제공형태 더보기-
표준
판매
ASTM D648-18
Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position- 발행일 : 2018-04-01
- 발행기관 : ASTM
상세정보
| 분야 | 08.01 : 플라스틱 (Ⅰ) |
|---|---|
| 적용범위 | 1.1 This test method covers the determination of the temperature at which an arbitrary deformation occurs when specimens are subjected to an arbitrary set of testing conditions. 1.2 This test method applies to molded and sheet materials available in thicknesses of 3 mm (1/8 in.) or greater and which are rigid or semirigid at normal temperature. Note 1: Sheet stock less than 3 mm (0.125 in.) but more than 1 mm (0.040 in.) in thickness may be tested by use of a composite sample having a minimum thickness of 3 mm. The laminae must be of uniform stress distribution. One type of composite specimen has been prepared by cementing the ends of the laminae together and then smoothing the edges with sandpaper. The direction of loading shall be perpendicular to the edges of the individual laminae. 1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only. 1.4 Some older machines still use mercury-in-glass thermometers. (Warning—Mercury has been designated by many regulatory agencies as a hazardous material that can cause serious medical issues. Mercury, or its vapor, has been demonstrated to be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Safety Data Sheet (SDS) for additional information. Users should be aware that selling mercury and/or mercury containing products into your state or country may be prohibited by law. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Note 2: The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. Note 3: This standard and ISO 75-1 and ISO 75-2 address the same subject matter, but differ in technical content, and results shall not be compared between the two test methods. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 83.080.01 : 플라스틱 일반 |
| 페이지수 | 14 |
| Edition | 18 |
이력정보
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D648-18 REDLINE상세보기 | Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position | 2018-04-01 | 표준 |
| 2 | ASTM D648-18상세보기 | Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position | 2018-04-01 | 표준 |
| 3 | ASTM D648-16상세보기 | Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position | 2016-04-01 | 구판 |
| 4 | ASTM D648-07상세보기 | Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position (Withdrawn 2016) | 2007-03-01 | 구판 |
| 5 | ASTM D648-06상세보기 | Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position | 2006-03-15 | 구판 |
| 6 | ASTM D648-04상세보기 | Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position | 2004-07-01 | 구판 |
| 7 | ASTM D648-00a상세보기 | Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position | 2001-08-10 | 구판 |
| 8 | ASTM D648-01상세보기 | Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position | 2001-08-10 | 구판 |
관련상품
- 관련상품이 존재하지 않습니다.
다른 사람이 함께 구입한 상품
- ASTM D1525-17e1 - Standard Test Method for Vicat Softening Temperature of Plastics
- ASTM D256-10(2018) - Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
- ASTM D638-14 - Standard Test Method for Tensile Properties of Plastics
- ASTM D790-17 - Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
- ASTM D785-08(2015) - Standard Test Method for Rockwell Hardness of Plastics and Electrical Insulating Materials
추천 상품
- IEC TS 63134:2020 - Active assisted living (AAL) use cases
- IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification
- KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs)
- KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs)
- KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스
제공형태 닫기
PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)보안PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능PRINT :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)BOOK :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)ZIP :
압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)CD/DVD :
직접 파일 다운로드 및 인쇄(마이페이지 확인)DB :
별도 정보 제공HARDCOPY :
해외 배송 상품, 최대 3주 소요바인더 :
바인더 우편발송, 2~3일 소요온라인구독 :
WEB 접속 후 실시간 열람, 출력(1년간)