QUICK

TOP

해외표준 상세정보

관심표준 등록 : 표준업데이트 시 알림서비스

제공형태 더보기
  • KS

    구판

    판매

    ASTM A572/A572M-18

    Standard Specification for High-Strength Low-Alloy Columbium-Vanadium Structural Steel
    • 발행일 : 2018-05-01
    • 발행기관 : ASTM
    즐겨찾기 장바구니 담기
    닫기

    상품이 장바구니에 담겼습니다.

    장바구니로 이동
    • [영어]PDF 116,700원

    • [영어]PRINT 116,700원

상세정보

분야 01.04 : 철강-구조물, 보강재, 압력용기, 철도
적용범위

1.1 This specification covers five grades of high-strength low-alloy structural steel shapes, plates, sheet piling, and bars. Grades 42 [290], 50 [345], and 55 [380] are intended for riveted, bolted, or welded structures. Grades 60 [415] and 65 [450] are intended for riveted or bolted construction of bridges, or for riveted, bolted, or welded construction in other applications.

1.2 For applications, such as welded bridge construction, where notch toughness is important, notch toughness requirements are to be negotiated between the purchaser and the producer.

1.3 Specification A588/A588M shall not be substituted for Specification A572/A572M without agreement between the purchaser and the supplier.

1.4 The use of columbium, vanadium, titanium, nitrogen, or combinations thereof, within the limitations noted in Section 5, is required; the selection of type (1, 2, 3, or 5) is at the option of the producer, unless otherwise specified by the purchaser. (See Supplementary Requirement S90.)

1.5 The maximum thicknesses available in the grades and products covered by this specification are shown in Table 1.

(A) In the above tabulation, Grades 42, 50, and 60 [290, 345, and 415], are the yield point levels most closely approximating a geometric progression pattern between 36 ksi [250 MPa], min, yield point steels covered by Specification A36/A36M and 100 ksi [690 MPa], min, yield strength steels covered by Specification A514/A514M.
(B) Round bars up to and including 11 in. [275 mm] in diameter are permitted.
(C) Round bars up to and including 31/2 in. [90 mm] in diameter are permitted.

1.6 When the steel is to be welded, a welding procedure suitable for the grade of steel and intended use or service is to be utilized. See Appendix X3 of Specification A6/A6M for information on weldability.

(A) Copper when specified shall have a minimum content of 0.20 % by heat analysis (0.18 % by product analysis).
(B) Manganese, minimum, by heat analysis of 0.80 % (0.75 % by product analysis) shall be required for all plates over 3/8 in. [10 mm] in thickness; a minimum of 0.50 % (0.45 % by product analysis) shall be required for plates 3/8 in. [10 mm] and less in thickness, and for all other products. The manganese to carbon ratio shall not be less than 2 to 1.
(C) Bars over 11/2 in. [40 mm] in diameter, thickness, or distance between parallel faces shall be made by a killed steel practice.
(D) For each reduction of 0.01 percentage point below the specified carbon maximum, an increase of 0.06 percentage point manganese above the specified maximum is permitted, up to a maximum of 1.60 %.
(E) Round bars up to and including 11 in. [275 mm] in diameter are permitted.
(F) Round bars up to and including 31/2 in. [90 mm] in diameter are permitted.
(G) The size and grade is not described in this specification.
(H) An alternative chemical requirement with a maximum carbon of 0.21 % and a maximum manganese of 1.65 % is permitted, with the balance of the elements as shown in Table 2.
(I) A maximum phosphorus content of 0.04 % and a maximum sulfur content of 0.05 % are permitted for the following materials:

· Structural shapes

· Sheet piling

· Bars

· Plates with widths up to and including 15 in. [380 mm]

1.7 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system is to be used independently of the other, without combining values in any way.

(A) Alloy content shall be in accordance with Type 1, 2, 3, or 5 and the contents of the applicable elements shall be reported on the test report.
(B) Product analysis limits = 0.004 to 0.06 %.
(C) Product analysis limits = 0.005 to 0.17%
(D) Product analysis limits = 0.01 to 0.16 %.

1.8 The text of this specification contains notes or footnotes, or both, that provide explanatory material. Such notes and footnotes, excluding those in tables and figures, do not contain any mandatory requirements.

(A) See specimen Orientation under the Tension Tests section of Specification A6/A6M.
(B) Elongation not required to be determined for floor plate.
(C) For wide flange shapes over 426 lb/ft [634 kg/m], elongation in 2 in. [50 mm] of 19 % minimum applies.
(D) For plates wider than 24 in. [600 mm], the elongation requirement is reduced two percentage points for Grades 42, 50, and 55 [290, 345, and 380], and three percentage points for Grades 60 and 65 [415 and 450]. See elongation requirement adjustments in the Tension Tests section of Specification A6/A6M.

1.9 For structural products produced from coil and furnished without heat treatment or with stress relieving only, the additional requirements, including additional testing requirements and the reporting of additional tests, of Specification A6/A6M apply.

1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

국제분류(ICS)코드 77.140.10 : 열처리용 강
페이지수 4
Edition 18

이력정보

No. 표준번호 표준명 발행일 상태
1 ASTM A572/A572M-21상세보기 Standard Specification for High-Strength Low-Alloy Columbium-Vanadium Structural Steel 2021-05-15 구판
2 ASTM A572/A572M-21e1상세보기 Standard Specification for High-Strength Low-Alloy Columbium-Vanadium Structural Steel 2021-05-15 표준
3 ASTM A572/A572M-21 REDLINE상세보기 Standard Specification for High-Strength Low-Alloy Columbium-Vanadium Structural Steel 2021-05-15 구판
4 ASTM A572/A572M-18 REDLINE상세보기 Standard Specification for High-Strength Low-Alloy Columbium-Vanadium Structural Steel 2018-05-01 구판
5 ASTM A572/A572M-18상세보기 Standard Specification for High-Strength Low-Alloy Columbium-Vanadium Structural Steel 2018-05-01 구판
6 ASTM A572/A572M-15상세보기 Standard Specification for High-Strength Low-Alloy Columbium-Vanadium Structural Steel 2015-03-01 구판
7 ASTM A572/A572M-13a상세보기 Standard Specification for High-Strength Low-Alloy Columbium-Vanadium Structural Steel 2013-11-01 구판
8 ASTM A572/A572M-13상세보기 Standard Specification for High-Strength Low-Alloy Columbium-Vanadium Structural Steel 2013-10-01 구판
9 ASTM A572/A572M-12a상세보기 Standard Specification for High-Strength Low-Alloy Columbium-Vanadium Structural Steel 2012-11-01 구판
10 ASTM A572/A572M-12상세보기 Standard Specification for High-Strength Low-Alloy Columbium-Vanadium Structural Steel 2012-05-01 구판
11 ASTM A572/A572M-07상세보기 Standard Specification for High-Strength Low-Alloy Columbium-Vanadium Structural Steel 2007-03-01 구판
12 ASTM A572/A572M-06상세보기 Standard Specification for High-Strength Low-Alloy Columbium-Vanadium Structural Steel 2006-03-01 구판
13 ASTM A572/A572M-04상세보기 Standard Specification for High-Strength Low-Alloy Columbium-Vanadium Structural Steel 2004-04-01 구판
14 ASTM A572/A572M-03ae1상세보기 Standard Specification for High-Strength Low-Alloy Columbium-Vanadium Structural Steel 2003-05-10 구판
15 ASTM A572/A572M-03a상세보기 Standard Specification for High-Strength Low-Alloy Columbium-Vanadium Structural Steel 2003-05-10 구판
16 ASTM A572/A572M-03상세보기 Standard Specification for High-Strength Low-Alloy Columbium-Vanadium Structural Steel 2003-04-10 구판
17 ASTM A572/A572M-02상세보기 Standard Specification for High-Strength Low-Alloy Columbium-Vanadium Structural Steel 2002-12-10 구판
18 ASTM A572/A572M-00a상세보기 Standard Specification for High-Strength Low-Alloy Columbium-Vanadium Structural Steel 2001-09-10 구판
19 ASTM A572/A572M-01상세보기 Standard Specification for High-Strength Low-Alloy Columbium-Vanadium Structural Steel 2001-09-10 구판

제공형태 닫기

  • PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)
  • 보안PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능
  • PRINT :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
  • BOOK :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
  • ZIP :

    압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)
  • CD/DVD :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)
  • DB :

    별도 정보 제공
  • HARDCOPY :

    해외 배송 상품, 최대 3주 소요
  • 바인더 :

    바인더 우편발송, 2~3일 소요
  • 온라인구독 :

    WEB 접속 후 실시간 열람, 출력(1년간)