관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
분야 | 14.05 : 통계 방법; 화학 물질의 잠재적 위험성; 열측정; 약품 제조 |
---|---|
적용범위 | 1.1 This test method covers the determination of specific heat capacity by differential scanning calorimetry. 1.2 This test method is generally applicable to thermally stable solids and liquids. 1.3 The normal operating range of the test is from − 100 to 600°C. The temperature range can be extended, depending upon the instrumentation and specimen holders used. 1.4 Computer or electronic-based instrumentation, techniques, or data treatment equivalent to this test method may be used. Note 1: Users of this test method are expressly advised that all such instruments or techniques may not be equivalent. It is the responsibility of the user of this test method to determine equivalency prior to use. 1.5 This test method is similar to ISO 11357–4, but contains additional methodology not found in that method. Additionally, ISO 11357–4 contains practices not found in this standard. This test method is similar to Japanese Industrial Standard K 7123, but contains additional methodology not found in that method. 1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 9. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
국제분류(ICS)코드 | |
페이지수 | 6 |
Edition | 11(2018) |
No. | 표준번호 | 표준명 | 발행일 | 상태 |
---|---|---|---|---|
1 | ASTM E1269-11(2018) | Standard Test Method for Determining Specific Heat Capacity by Differential Scanning Calorimetry | 2018-04-01 | 표준 |
2 | ASTM E1269-11 | Standard Test Method for Determining Specific Heat Capacity by Differential Scanning Calorimetry | 2011-04-01 | 구판 |
3 | ASTM E1269-05 | Standard Test Method for Determining Specific Heat Capacity by Differential Scanning Calorimetry | 2005-03-01 | 구판 |
4 | ASTM E1269-04 | Standard Test Method for Determining Specific Heat Capacity by Differential Scanning Calorimetry | 2004-06-01 | 구판 |
5 | ASTM E1269-99 | Standard Test Method for Determining Specific Heat Capacity by Differential Scanning Calorimetry | 2001-02-10 | 구판 |
6 | ASTM E1269-01 | Standard Test Method for Determining Specific Heat Capacity by Differential Scanning Calorimetry | 2001-02-10 | 구판 |
관련상품이 존재하지 않습니다.
KS R 4024(2019 확인) - 자동차용 브레이크 라이닝 및 패드 상세보기
KS L ISO 5017(2018 확인) - 치밀질 정형 내화 제품의 부피 밀도, 겉보기 기공률 및 참 기공률 시험방법 상세보기
ASTM C20-00(2022) - Standard Test Methods for Apparent Porosity, Water Absorption, Apparent Specific Gravity, and Bulk Density of Burned Refractory Brick and Shapes by Boiling Water 상세보기
ASTM D790-17 - Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials 상세보기
ASTM D3702-94(2019) - Standard Test Method for Wear Rate and Coefficient of Friction of Materials in Self-Lubricated Rubbing Contact Using a Thrust Washer Testing Machine 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기