사업자등록증
해외표준
FAQ
장바구니
고객센터
해외표준 상세정보
관심표준 등록 : 표준업데이트 시 알림서비스
제공형태 더보기-
폐지
판매
ASTM F2812-12(2018)
Standard Specification for Goggle- and Spectacle-Type Eye Protectors for Selected Motor Sports (Withdrawn 2024)- 발행일 : 2018-04-01 (2024-07-25 폐지)
- 발행기관 : ASTM
상세정보
| 분야 | 15.07 : 스포츠 장비와 시설, 보행자 보도 안전과 신발 안전, 놀이 기구 |
|---|---|
| 적용범위 | 1.1 This specification covers eye protectors, exclusive of helmet-mounted visors, designed for use by riders of motorcycles, mopeds, and snowmobiles for off road use that minimize or significantly reduce injury to the eye and adnexa as a result of impact and penetration by objects that may be kicked up from the road, track, trail, or snow surfaces and made airborne and, as such, likely to cause eye discomfort or injury. This specification does not address shield-type eye protectors such as are connected to, integral to, and/or supported by protective helmets. Protective eyewear offers protection only to the eyes and does not protect other parts of the head, face, or neck. 1.2 Protectors are divided into two types, goggles or spectacles, depending on their design characteristics. 1.3 This specification does not apply to prescription eyewear. (Warning—Impact-resistant prescription spectacles that conform to the standard specifications of ANSI Z87.1 should be used if spectacles are to be worn under goggle-type eyewear as covered by this specification.) 1.4 In this specification, the use of the word “shall” indicates a mandatory requirement. The word “should” indicates a recommendation. 1.5 Units—The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. Metric units of measure in this specification are in accordance with the International System of Units (SI). If a value for measurement as given in this specification is followed by an equivalent value in other units, the first stated is to be regarded as the requirement. A given equivalent value may be approximate. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 13.340.20 : 보호 장비 |
| 페이지수 | 6 |
| Edition | 12(2018) |
이력정보
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM F2812-12(2018)상세보기 | Standard Specification for Goggle- and Spectacle-Type Eye Protectors for Selected Motor Sports (Withdrawn 2024) | 2018-04-01 | 폐지 |
| 2 | ASTM F2812-12상세보기 | Standard Specification for Goggle- and Spectacle-Type Eye Protectors for Selected Motor Sports | 2012-07-01 | 구판 |
관련상품
- 관련상품이 존재하지 않습니다.
다른 사람이 함께 구입한 상품
- ASTM E3299/E3299M-21a - Standard Test Methods for Compression Resistance of Helmets
- DIN EN 17128:2021-01 - Light motorized vehicles for the transportation of persons and goods and related facilities and not subject to type-approval for on-road use - Personal light electric vehicles (PLEV) - Requirements and test methods
- ASTM F910-04(2015) - Standard Specification for Face Guards for Youth Baseball
- ISO 10256-1:2016 - Protective equipment for use in ice hockey — Part 1: General requirements
- ASTM F2220-15 - Standard Specification for Headforms
추천 상품
- IEC TS 63134:2020 - Active assisted living (AAL) use cases
- IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification
- KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs)
- KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs)
- KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스
제공형태 닫기
PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)보안PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능PRINT :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)BOOK :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)ZIP :
압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)CD/DVD :
직접 파일 다운로드 및 인쇄(마이페이지 확인)DB :
별도 정보 제공HARDCOPY :
해외 배송 상품, 최대 3주 소요바인더 :
바인더 우편발송, 2~3일 소요온라인구독 :
WEB 접속 후 실시간 열람, 출력(1년간)