한국표준정보망

회원가입 로그인 비회원(주문조회) 장바구니 이용안내

English
메뉴
검색 마이페이지 장바구니0

QUICK

닫기

TOP

해외표준 상세정보

관심표준 등록 : 표준업데이트 시 알림서비스

제공형태 더보기

  • KS

    표준

    판매

    ASTM B955/B955M-18

    Standard Specification for Aluminum-Alloy Centrifugal Castings
    • 발행일 : 2018-05-15
    • 발행기관 : ASTM
    즐겨찾기 장바구니 담기
    닫기

    상품이 장바구니에 담겼습니다.

    장바구니로 이동

    • [영어]PDF 117,300원

    • [영어]PRINT 117,300원

상세정보

분야 02.02 : 알루미늄 및 마그네슘 합금
적용범위

1.1 This specification covers aluminum-alloy centrifugal castings designated as shown in Table 1.

(A) When single units are shown, these indicate the maximum amounts permitted.
(B) Analysis shall be made for the elements for which limits are shown in this table.
(C) The following applies to all specified limits in this table: For purposes of determining conformance to these limits, an observed value or a calculated value obtained from analysis shall be rounded to the nearest unit in the last right-hand place of figures used in expressing the specified limit in accordance with the rounding method of Practice E29.
(D) In case of discrepancy between the values listed in Table 1 and those listed in the “Designations and Composition Limits for Aluminum Alloys in the Form of Castings and Ingot (known as the ‘Pink Sheets’),” the composition limits registered with the Aluminum Association and published in the “Pink Sheets” shall be considered the controlling composition.
(E) “Others” includes listed elements for which no specific limit is shown as well as unlisted metallic elements. The producer may analyze samples for trace elements not specified in the specification. However, such analysis is not required and may not cover all metallic “Others” elements. Should any analysis by the producer or the purchaser establish that an “Others” element exceeds the limit of “Each” or that the aggregate of several “Others” elements exceeds the limit of “Total,” the material shall be considered nonconforming.
(F) Other Elements—Total shall be the sum of unspecified metallic elements 0.010 % or more, rounded to the second decimal before determining the sum.
(G) If the iron content exceeds 0.45 %, manganese content shall not be less than one half of the iron.
(H) For a cross reference of current and former alloy designations see the Aluminum Association’s “Designations and Chemical Composition Limits for Aluminum Alloys in the Form of Castings and Ingot (‘The Pink Sheets’).”

1.2 This specification is for aluminum-alloy centrifugal castings used in general purpose applications. It may not address the mechanical properties, integrity testing, and verification required for highly loaded or safety critical applications.

1.3 Alloy and temper designations are in accordance with ANSI H35.1/H35.1 (M).

1.4 Unless the order specifies the “M” specification designation, the material shall be furnished to the inch-pound units.

1.5 For acceptance criteria for inclusion of new aluminum and aluminum alloys and their properties in this specification, see Annex A1 and Annex A2.

1.6 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
국제분류(ICS)코드 77.150.10 : 알루미늄 제품
페이지수 11
Edition 18

이력정보

No. 표준번호 표준명 발행일 상태
1 ASTM B955/B955M-18상세보기 Standard Specification for Aluminum-Alloy Centrifugal Castings 2018-05-15 표준
2 ASTM B955/B955M-14상세보기 Standard Specification for Aluminum-Alloy Centrifugal Castings 2014-10-01 구판
3 ASTM B955/B955M-11상세보기 Standard Specification for Aluminum-Alloy Centrifugal Castings 2011-05-01 구판
4 ASTM B955/B955M-10상세보기 Standard Specification for Aluminum-Alloy Centrifugal Castings 2010-11-01 구판
5 ASTM B955/B955M-08상세보기 Standard Specification for Aluminum-Alloy Centrifugal Castings 2008-07-15 구판
6 ASTM B955/B955M-07상세보기 Standard Specification for Aluminum-Alloy Centrifugal Castings 2007-10-01 구판

관련상품

  • 관련상품이 존재하지 않습니다.

다른 사람이 함께 구입한 상품

추천 상품

제공형태 닫기

  • PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)

  • 보안PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능

  • PRINT :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

  • BOOK :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

  • ZIP :

    압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)

  • CD/DVD :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)

  • DB :

    별도 정보 제공

  • HARDCOPY :

    해외 배송 상품, 최대 3주 소요

  • 바인더 :

    바인더 우편발송, 2~3일 소요

  • 온라인구독 :

    WEB 접속 후 실시간 열람, 출력(1년간)