사업자등록증
해외표준
FAQ
장바구니
고객센터
해외표준 상세정보
관심표준 등록 : 표준업데이트 시 알림서비스
제공형태 더보기-
구판
판매
ASTM C1273-18
Standard Test Method for Tensile Strength of Monolithic Advanced Ceramics at Ambient Temperatures- 발행일 : 2018-07-01
- 발행기관 : ASTM
상세정보
| 분야 | 15.01 : 내화물; 활성카본; 세라믹 |
|---|---|
| 적용범위 | 1.1 This test method covers the determination of tensile strength under uniaxial loading of monolithic advanced ceramics at ambient temperatures. This test method addresses, but is not restricted to, various suggested test specimen geometries as listed in the appendixes. In addition, test specimen fabrication methods, testing modes (force, displacement, or strain control), testing rates (force rate, stress rate, displacement rate, or strain rate), allowable bending, and data collection and reporting procedures are addressed. Note that tensile strength as used in this test method refers to the tensile strength obtained under uniaxial loading. 1.2 This test method applies primarily to advanced ceramics that macroscopically exhibit isotropic, homogeneous, continuous behavior. While this test method applies primarily to monolithic advanced ceramics, certain whisker- or particle-reinforced composite ceramics as well as certain discontinuous fiber-reinforced composite ceramics may also meet these macroscopic behavior assumptions. Generally, continuous fiber ceramic composites (CFCCs) do not macroscopically exhibit isotropic, homogeneous, continuous behavior and application of this practice to these materials is not recommended. 1.3 Values expressed in this test method are in accordance with the International System of Units (SI) and IEEE/ASTM SI 10. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 7. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 |
81.060.30 : 고급 세라믹
81.060.99 : 세라믹 관련 기타 표준 |
| 페이지수 | 19 |
| Edition | 18 |
이력정보
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM C1273-18(2024)상세보기 | Standard Test Method for Tensile Strength of Monolithic Advanced Ceramics at Ambient Temperatures | 2024-08-01 | 표준 |
| 2 | ASTM C1273-18상세보기 | Standard Test Method for Tensile Strength of Monolithic Advanced Ceramics at Ambient Temperatures | 2018-07-01 | 구판 |
| 3 | ASTM C1273-18 REDLINE상세보기 | Standard Test Method for Tensile Strength of Monolithic Advanced Ceramics at Ambient Temperatures | 2018-07-01 | 구판 |
| 4 | ASTM C1273-15상세보기 | Standard Test Method for Tensile Strength of Monolithic Advanced Ceramics at Ambient Temperatures | 2015-07-01 | 구판 |
| 5 | ASTM C1273-05(2010)상세보기 | Standard Test Method for Tensile Strength of Monolithic Advanced Ceramics at Ambient Temperatures | 2010-06-01 | 구판 |
| 6 | ASTM C1273-05상세보기 | Standard Test Method for Tensile Strength of Monolithic Advanced Ceramics at Ambient Temperatures | 2005-06-01 | 구판 |
| 7 | ASTM C1273-95a(2000)상세보기 | Standard Test Method for Tensile Strength of Monolithic Advanced Ceramics at Ambient Temperatures | 2000-01-01 | 구판 |
관련상품
- 관련상품이 존재하지 않습니다.
다른 사람이 함께 구입한 상품
- ASTM D790-17 - Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
- ASTM C1161-18 - Standard Test Method for Flexural Strength of Advanced Ceramics at Ambient Temperature
- ASTM C1424-15(2019) - Standard Test Method for Monotonic Compressive Strength of Advanced Ceramics at Ambient Temperature
- IEC TR 60071-4:2004 - Insulation co-ordination - Part 4: Computational guide to insulation co-ordination and modelling of electrical networks
- DIN EN 12201-1:2011-11 - Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 1: General
추천 상품
- IEC TS 63134:2020 - Active assisted living (AAL) use cases
- IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification
- KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs)
- KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs)
- KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스
제공형태 닫기
PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)보안PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능PRINT :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)BOOK :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)ZIP :
압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)CD/DVD :
직접 파일 다운로드 및 인쇄(마이페이지 확인)DB :
별도 정보 제공HARDCOPY :
해외 배송 상품, 최대 3주 소요바인더 :
바인더 우편발송, 2~3일 소요온라인구독 :
WEB 접속 후 실시간 열람, 출력(1년간)