사업자등록증
해외표준
FAQ
장바구니
고객센터
해외표준 상세정보
관심표준 등록 : 표준업데이트 시 알림서비스
제공형태 더보기-
표준
판매
ASTM D882-18
Standard Test Method for Tensile Properties of Thin Plastic Sheeting- 발행일 : 2018-08-01
- 발행기관 : ASTM
상세정보
| 분야 | 08.01 : 플라스틱 (Ⅰ) |
|---|---|
| 적용범위 | 1.1 This test method covers the determination of tensile properties of plastics in the form of thin sheeting and films (less than 1.0 mm (0.04 in.) in thickness). Note 1: Film is defined in Terminology D883 as an optional term for sheeting having a nominal thickness no greater than 0.25 mm (0.010 in.). Note 2: Tensile properties of plastics 1.0 mm (0.04 in.) or greater in thickness shall be determined according to Test Method D638. 1.2 This test method can be used to test all plastics within the thickness range described and the capacity of the machine employed. 1.3 Specimen extension can be measured by grip separation, extension indicators, or displacement of gage marks. 1.4 The procedure for determining the tensile modulus of elasticity is included at one strain rate. Note 3: The modulus determination is generally based on the use of grip separation as a measure of extension; however, the desirability of using extensometers, as described in 6.2, is recognized and provision for the use of such instrumentation is incorporated in the procedure. 1.5 Test data obtained by this test method is relevant and appropriate for use in engineering design. 1.6 The values stated in SI units are to be regarded as the standard. The values in parentheses are provided for information only. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Note 4: This test method is similar to ISO 527-3, but is not considered technically equivalent. ISO 527-3 allows for additional specimen configurations, specifies different test speeds, and requires an extensometer or gage marks on the specimen. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | |
| 페이지수 | 12 |
| Edition | 18 |
이력정보
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D882-18 REDLINE상세보기 | Standard Test Method for Tensile Properties of Thin Plastic Sheeting | 2018-08-01 | 표준 |
| 2 | ASTM D882-18상세보기 | Standard Test Method for Tensile Properties of Thin Plastic Sheeting | 2018-08-01 | 표준 |
| 3 | ASTM D882-12상세보기 | Standard Test Method for Tensile Properties of Thin Plastic Sheeting | 2012-08-01 | 구판 |
| 4 | ASTM D882-10상세보기 | Standard Test Method for Tensile Properties of Thin Plastic Sheeting | 2010-04-01 | 구판 |
| 5 | ASTM D882-09상세보기 | Standard Test Method for Tensile Properties of Thin Plastic Sheeting | 2009-01-01 | 구판 |
| 6 | ASTM D882-00상세보기 | Standard Test Method for Tensile Properties of Thin Plastic Sheeting | 2002-04-10 | 구판 |
| 7 | ASTM D882-01상세보기 | Standard Test Method for Tensile Properties of Thin Plastic Sheeting | 2002-04-10 | 구판 |
| 8 | ASTM D882-02상세보기 | Standard Test Method for Tensile Properties of Thin Plastic Sheeting | 2002-04-10 | 구판 |
| 9 | ASTM D882-97상세보기 | Standard Test Method for Tensile Properties of Thin Plastic Sheeting | 구판 |
관련상품
- 관련상품이 존재하지 않습니다.
다른 사람이 함께 구입한 상품
- ISO 527-1:2019 - Plastics — Determination of tensile properties — Part 1: General principles
- ASTM D1204-14(2020) - Standard Test Method for Linear Dimensional Changes of Nonrigid Thermoplastic Sheeting or Film at Elevated Temperature
- ASTM D1922-15(2020) - Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
- ASTM D792-20 - Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
- ASTM D1003-21 - Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics
추천 상품
- IEC TS 63134:2020 - Active assisted living (AAL) use cases
- IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification
- KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs)
- KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs)
- KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스
제공형태 닫기
PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)보안PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능PRINT :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)BOOK :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)ZIP :
압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)CD/DVD :
직접 파일 다운로드 및 인쇄(마이페이지 확인)DB :
별도 정보 제공HARDCOPY :
해외 배송 상품, 최대 3주 소요바인더 :
바인더 우편발송, 2~3일 소요온라인구독 :
WEB 접속 후 실시간 열람, 출력(1년간)