한국표준정보망

회원가입 로그인 비회원(주문조회) 장바구니 이용안내

English
메뉴
검색 마이페이지 장바구니0

QUICK

닫기

TOP

해외표준 상세정보

관심표준 등록 : 표준업데이트 시 알림서비스

제공형태 더보기

  • KS

    표준

    판매

    ASTM G76-18

    Standard Test Method for Conducting Erosion Tests by Solid Particle Impingement Using Gas Jets
    • 발행일 : 2018-10-01
    • 발행기관 : ASTM
    즐겨찾기 장바구니 담기
    닫기

    상품이 장바구니에 담겼습니다.

    장바구니로 이동

    • [영어]PDF 109,400원

    • [영어]PRINT 109,400원

상세정보

분야 03.02 : 마모 및 침식;금속 부식
적용범위

1.1 This test method covers the determination of material loss by gas-entrained solid particle impingement erosion with jetnozzle type erosion equipment. This test method may be used in the laboratory to measure the solid particle erosion of different materials and has been used as a screening test for ranking solid particle erosion rates of materials in simulated service environments (1, 2).2 Actual erosion service involves particle sizes, velocities, attack angles, environments, and so forth, that will vary over a wide range (3-5). Hence, any single laboratory test may not be sufficient to evaluate expected service performance. This test method describes one well characterized procedure for solid particle impingement erosion measurement for which interlaboratory test results are available.

1.2 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard (exceptions below).

1.2.1 Exceptions: Table 1 uses HRB hardness. Footnote 7 and 11.2 use abrasive grit designations.

1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
국제분류(ICS)코드
페이지수 6
Edition 18

이력정보

No. 표준번호 표준명 발행일 상태
1 ASTM G76-18 REDLINE상세보기 Standard Test Method for Conducting Erosion Tests by Solid Particle Impingement Using Gas Jets 2018-10-01 표준
2 ASTM G76-18상세보기 Standard Test Method for Conducting Erosion Tests by Solid Particle Impingement Using Gas Jets 2018-10-01 표준
3 ASTM G76-13상세보기 Standard Test Method for Conducting Erosion Tests by Solid Particle Impingement Using Gas Jets 2013-07-01 구판
4 ASTM G76-07상세보기 Standard Test Method for Conducting Erosion Tests by Solid Particle Impingement Using Gas Jets 2007-07-01 구판
5 ASTM G76-05상세보기 Standard Test Method for Conducting Erosion Tests by Solid Particle Impingement Using Gas Jets 2005-11-01 구판
6 ASTM G76-04상세보기 Standard Test Method for Conducting Erosion Tests by Solid Particle Impingement Using Gas Jets 2004-01-01 구판
7 ASTM G76-02상세보기 Standard Test Method for Conducting Erosion Tests by Solid Particle Impingement Using Gas Jets 2002-11-10 구판
8 ASTM G76-95상세보기 Standard Test Method for Conducting Erosion Tests by Solid Particle Impingement Using Gas Jets 2000-01-01 구판
9 ASTM G76-95(2000)상세보기 Standard Test Method for Conducting Erosion Tests by Solid Particle Impingement Using Gas Jets 2000-01-01 구판

관련상품

  • 관련상품이 존재하지 않습니다.

다른 사람이 함께 구입한 상품

추천 상품

제공형태 닫기

  • PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)

  • 보안PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능

  • PRINT :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

  • BOOK :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

  • ZIP :

    압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)

  • CD/DVD :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)

  • DB :

    별도 정보 제공

  • HARDCOPY :

    해외 배송 상품, 최대 3주 소요

  • 바인더 :

    바인더 우편발송, 2~3일 소요

  • 온라인구독 :

    WEB 접속 후 실시간 열람, 출력(1년간)