사업자등록증
해외표준
FAQ
장바구니
고객센터
해외표준 상세정보
관심표준 등록 : 표준업데이트 시 알림서비스
제공형태 더보기-
구판
판매
ASTM F3123-18
Standard Specification for Metric Outside Diameter Polyethylene (PE) Plastic Pipe (DR-PN)- 발행일 : 2018-04-01
- 발행기관 : ASTM
상세정보
| 분야 | 08.04 : 플라스틱 파이프 및 건축용 제품 |
|---|---|
| 적용범위 | 1.1 This specification covers metric outside diameter polyethylene (PE) pipe made from polyethylene compound that qualifies for MRS, HDB and HDS ratings and for PE100 and PE4710 designations. Included are requirements for polyethylene compound, workmanship, dimensions, short-term stress and ductility, long-term stress, marking, quality assurance and verification of joining. 1.1.1 Polyethylene pipe in accordance with this specification is intended to be compatible with nominal diameters and nominal pressures in accordance with ISO 161-1 and wall thickness in accordance with ISO 4065. 1.2 Pipes produced under this specification are intended for the pressure or non-pressure conveyance of liquid or gaseous media. Pipes produced under this specification are not intended as enclosures for electrical or communications components. See Appendix X1. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 The ANS label on this international standard certifies the development of this international standard in accordance with requirements for openness, balance, consensus and due process in accordance with ANSI Essential Requirements: Due Process Requirements for American National Standards and denotes in addition that this international standard is an American National Standard. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | |
| 페이지수 | 12 |
| Edition | 18 |
이력정보
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM F3123-22상세보기 | Standard Specification for Metric Outside Diameter Polyethylene (PE) Plastic Pipe (DR-PN) | 2022-02-01 | 표준 |
| 2 | ASTM F3123-22 REDLINE상세보기 | Standard Specification for Metric Outside Diameter Polyethylene (PE) Plastic Pipe (DR-PN) | 2022-02-01 | 표준 |
| 3 | ASTM F3123-18a REDLINE상세보기 | Standard Specification for Metric Outside Diameter Polyethylene (PE) Plastic Pipe (DR-PN) | 2018-11-01 | 구판 |
| 4 | ASTM F3123-18a상세보기 | Standard Specification for Metric Outside Diameter Polyethylene (PE) Plastic Pipe (DR-PN) | 2018-11-01 | 구판 |
| 5 | ASTM F3123-18상세보기 | Standard Specification for Metric Outside Diameter Polyethylene (PE) Plastic Pipe (DR-PN) | 2018-04-01 | 구판 |
| 6 | ASTM F3123-16상세보기 | Standard Specification for Metric Outside Diameter Polyethylene (PE) Plastic Pipe (DR-PN) | 2016-11-01 | 구판 |
| 7 | ASTM F3123-15a상세보기 | Standard Specification for Metric Outside Diameter Polyethylene (PE) Plastic Pipe (DR-PN) | 2015-11-01 | 구판 |
| 8 | ASTM F3123-15상세보기 | Standard Specification for Metric Outside Diameter Polyethylene (PE) Plastic Pipe (DR-PN) | 2015-05-01 | 구판 |
관련상품
- 관련상품이 존재하지 않습니다.
다른 사람이 함께 구입한 상품
- 함께 구입한 상품이 존재하지 않습니다.
추천 상품
- IEC TS 63134:2020 - Active assisted living (AAL) use cases
- IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification
- KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs)
- KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs)
- KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스
제공형태 닫기
PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)보안PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능PRINT :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)BOOK :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)ZIP :
압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)CD/DVD :
직접 파일 다운로드 및 인쇄(마이페이지 확인)DB :
별도 정보 제공HARDCOPY :
해외 배송 상품, 최대 3주 소요바인더 :
바인더 우편발송, 2~3일 소요온라인구독 :
WEB 접속 후 실시간 열람, 출력(1년간)