한국표준정보망

회원가입 로그인 비회원(주문조회) 장바구니 이용안내

English
메뉴
검색 마이페이지 장바구니0

QUICK

닫기

TOP

해외표준 상세정보

관심표준 등록 : 표준업데이트 시 알림서비스

제공형태 더보기

  • KS

    구판

    판매

    ASTM E3078/E3078M-19

    Standard Practice for Conditioning of Hard Armor Test Items
    • 발행일 : 2019-05-01
    • 발행기관 : ASTM
    즐겨찾기 장바구니 담기
    닫기

    상품이 장바구니에 담겼습니다.

    장바구니로 이동

    • [영어]PDF 131,600원

    • [영어]PRINT 131,600원

상세정보

분야 15.08 : 감지측정, 진공청소기, 안전 시스템
적용범위

1.1 This practice applies to the conditioning of hard armor test items prior to ballistic resistance testing. Hard armor is an item of personal protective equipment that is constructed of rigid materials and is intended to protect the wearer from threats that may include ballistic threats, stabbing, fragmentation, or blunt impact, or combinations thereof. (Terminology E3005.) Hard armor is also referred to as hard armor plate and plate.

Note—Ballistic resistance testing is not covered in this practice.

1.2 This practice describes requirements for subjecting test items to conditions intended to assess the capability of the test item to withstand environmental conditions that induce responses similar to those that might result from conditions encountered during use. This practice includes the conditioning procedures listed below:

(1) Controlled ambient conditioning procedure,

(2) Thermal/temperature shock procedure,

(3) Temperature extremes procedure,

(4) Weathering procedure,

(5) Fluid exposure procedure,

(6) Altitude exposure procedure,

(7) Vibration conditioning procedure,

(8) Impact Durability pre-conditioning,

(9) Impact Durability procedure for torso front and back plates, and

(10) Impact Durability procedure for other plates (that is, other than torso front and back plates).

1.3 The user of this practice shall determine which conditioning procedures apply.

Note—This practice may not be applicable to all types of hard armor.

1.4 In this practice, “other standards and specifications” and “unless specified elsewhere” refer to documents (for example, military standards, purchase specifications) that require the use of this practice. Purchasers and other users are responsible for the “other standards and specifications” and for specifying any requirements that supersede those of this practice.

1.5 This practice does not address pass/fail requirements for test items subjected to these procedures.

1.6 This practice does not address visual inspections or radiographic inspections of test items that may be required prior to or following conditioning.

Note—It is recommended that a thorough visual examination of each test item prior to and after the exposures be performed to document any change in physical appearance resulting from the exposure.

1.7 This practice does not address subsequent conditioning or testing of test items.

1.8 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.

1.8.1 The user of this standard will identify the system of units to be used, and it is critical to ensure that any cross-referenced standards maintain consistency of units between standards.

1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
국제분류(ICS)코드 13.310 : 범죄로부터의 보호
13.340.01 : 보호장비 일반
페이지수 7
Edition 19

이력정보

No. 표준번호 표준명 발행일 상태
1 ASTM E3078/E3078M-23상세보기 Standard Practice for Conditioning of Hard Armor Test Items 2023-02-01 표준
2 ASTM E3078/E3078M-23 REDLINE상세보기 Standard Practice for Conditioning of Hard Armor Test Items 2023-02-01 표준
3 ASTM E3078/E3078M-22상세보기 Standard Practice for Conditioning of Hard Armor Test Items 2022-10-01 구판
4 ASTM E3078/E3078M-22 REDLINE상세보기 Standard Practice for Conditioning of Hard Armor Test Items 2022-10-01 구판
5 ASTM E3078/E3078M-20e1상세보기 Standard Practice for Conditioning of Hard Armor Test Items 2020-04-01 구판
6 ASTM E3078/E3078M-20상세보기 Standard Practice for Conditioning of Hard Armor Test Items 2020-04-01 구판
7 ASTM E3078/E3078M-20 REDLINE상세보기 Standard Practice for Conditioning of Hard Armor Test Items 2020-04-01 구판
8 ASTM E3078/E3078M-19상세보기 Standard Practice for Conditioning of Hard Armor Test Items 2019-05-01 구판
9 ASTM E3078/E3078M-19 REDLINE상세보기 Standard Practice for Conditioning of Hard Armor Test Items 2019-05-01 구판

관련상품

  • 관련상품이 존재하지 않습니다.

다른 사람이 함께 구입한 상품

  • 함께 구입한 상품이 존재하지 않습니다.

추천 상품

제공형태 닫기

  • PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)

  • 보안PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능

  • PRINT :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

  • BOOK :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

  • ZIP :

    압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)

  • CD/DVD :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)

  • DB :

    별도 정보 제공

  • HARDCOPY :

    해외 배송 상품, 최대 3주 소요

  • 바인더 :

    바인더 우편발송, 2~3일 소요

  • 온라인구독 :

    WEB 접속 후 실시간 열람, 출력(1년간)