사업자등록증
해외표준
FAQ
장바구니
고객센터
해외표준 상세정보
관심표준 등록 : 표준업데이트 시 알림서비스
제공형태 더보기-
구판
판매
ASTM A428/A428M-10(2019)
Standard Test Method for Weight [Mass] of Coating on Aluminum-Coated Iron or Steel Articles- 발행일 : 2019-05-01
- 발행기관 : ASTM
상세정보
| 분야 | 01.06 : 피복 철강 제품 |
|---|---|
| 적용범위 | 1.1 This test method covers procedures for determining the weight [mass] of coating on aluminum-coated iron or steel sheets and wire, and on other aluminum-coated iron and steel articles. 1.2 The final results determined by this test method shall be expressed in inch-pound units or SI units, depending on the units used in the material specification to which the results are to be compared. Certain portions of the procedure involving determination of specimen weight [mass] have traditionally been performed in SI units, and corresponding inch-pound units are not included. 1.3 For sheet products, the final results are expressed as either coating weight [mass] total both sides, or coating weight [mass] separately on each side, depending on the specified requirements. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For a specific precautionary statement, see Note 1. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 25.220.40 : 금속 도장 |
| 페이지수 | 6 |
| Edition | 10(2019) |
이력정보
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM A428/A428M-21상세보기 | Standard Test Method for Weight [Mass] of Coating on Aluminum-Coated Iron or Steel Articles | 2021-05-01 | 표준 |
| 2 | ASTM A428/A428M-21 REDLINE상세보기 | Standard Test Method for Weight [Mass] of Coating on Aluminum-Coated Iron or Steel Articles | 2021-05-01 | 표준 |
| 3 | ASTM A428/A428M-10(2019)상세보기 | Standard Test Method for Weight [Mass] of Coating on Aluminum-Coated Iron or Steel Articles | 2019-05-01 | 구판 |
| 4 | ASTM A428/A428M-10(2014)상세보기 | Standard Test Method for Weight [Mass] of Coating on Aluminum-Coated Iron or Steel Articles | 2014-08-01 | 구판 |
| 5 | ASTM A428/A428M-10상세보기 | Standard Test Method for Weight [Mass] of Coating on Aluminum-Coated Iron or Steel Articles | 2010-05-01 | 구판 |
| 6 | ASTM A428/A428M-06상세보기 | Standard Test Method for Weight [Mass] of Coating on Aluminum-Coated Iron or Steel Articles | 2006-11-01 | 구판 |
| 7 | ASTM A428/A428M-95상세보기 | Standard Test Method for Weight [Mass] of Coating on Aluminum-Coated Iron or Steel Articles | 2001-04-10 | 구판 |
| 8 | ASTM A428/A428M-01상세보기 | Standard Test Method for Weight [Mass] of Coating on Aluminum-Coated Iron or Steel Articles | 2001-04-10 | 구판 |
관련상품
- 관련상품이 존재하지 않습니다.
다른 사람이 함께 구입한 상품
- JIS G 3193:2019 - Dimensions, shape, mass and permissible variations of hot rolled steel plates, sheets and strips
- AS 2883-2000 (R2016) - Analysis of metals - Procedures for the setting up, calibration and standardization of atomic emission spectrometers using arc/spark discharge
- ASTM A879/A879M-12(2017) - Standard Specification for Steel Sheet, Zinc Coated by the Electrolytic Process for Applications Requiring Designation of the Coating Mass on Each Surface
- JIS C 2553:2019 - Cold-rolled grain-oriented electrical steel strip and sheet delivered in the fully-processed state
- DIN EN 10025-2:2019-10 - Hot rolled products of structural steels - Part 2: Technical delivery conditions for non-alloy structural steels
추천 상품
- IEC TS 63134:2020 - Active assisted living (AAL) use cases
- IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification
- KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs)
- KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs)
- KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스
제공형태 닫기
PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)보안PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능PRINT :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)BOOK :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)ZIP :
압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)CD/DVD :
직접 파일 다운로드 및 인쇄(마이페이지 확인)DB :
별도 정보 제공HARDCOPY :
해외 배송 상품, 최대 3주 소요바인더 :
바인더 우편발송, 2~3일 소요온라인구독 :
WEB 접속 후 실시간 열람, 출력(1년간)