관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
분야 | 09.01 : 고무, 자연 및 합성-일반시험 방법, 카본블랙 |
---|---|
적용범위 | 1.1 This practice is intended for use in determining the geometrical dimensions of rubber products and specimens for physical tests. This practice describes procedures for determining length, width, thickness, diameter, and circumference. This practice does not cover sampling of materials or products, or locations where a sample is to be taken. 1.2 The values stated in either acceptable metric units or in other units shall be regarded separately as a standard. The values stated in each system may not be exact equivalents; therefore, each system must be used independently of the other, without combining values in any other way. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
국제분류(ICS)코드 | 83.060 : 고무 |
페이지수 | 8 |
Edition | 03(2020) |
No. | 표준번호 | 표준명 | 발행일 | 상태 |
---|---|---|---|---|
1 | ASTM D3767-03(2020) | Standard Practice for Rubber—Measurement of Dimensions | 2020-02-01 | 표준 |
2 | ASTM D3767-03(2014) | Standard Practice for Rubber—Measurement of Dimensions | 2014-11-01 | 구판 |
3 | ASTM D3767-03(2008) | Standard Practice for Rubber—Measurement of Dimensions | 2008-05-01 | 구판 |
4 | ASTM D3767-03 | Standard Practice for Rubber-Measurement of Dimensions | 2003-12-01 | 구판 |
5 | ASTM D3767-96 | Standard Practice for Rubber-Measurement of Dimensions | 2001-01-10 | 구판 |
6 | ASTM D3767-01 | Standard Practice for Rubber-Measurement of Dimensions | 2001-01-10 | 구판 |
관련상품이 존재하지 않습니다.
ASTM D1148-13(2018) - Standard Test Method for Rubber Deterioration—Discoloration from Ultraviolet (UV) or UV/Visible Radiation and Heat Exposure of Light-Colored Surfaces 상세보기
ASTM D523-14(2018) - Standard Test Method for Specular Gloss 상세보기
ASTM D4970/D4970M-16e3 - Standard Test Method for Pilling Resistance and Other Related Surface Changes of Textile Fabrics: Martindale Tester 상세보기
ASTM D4966-12(2016) - Standard Test Method for Abrasion Resistance of Textile Fabrics (Martindale Abrasion Tester Method) 상세보기
ASTM E1809-01 - Standard Test Method for Measurement of High-Visibility Retroreflective-Clothing Marking Material Using a Portable Retroreflectometer (Withdrawn 2010) 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기