사업자등록증
해외표준
FAQ
장바구니
고객센터
해외표준 상세정보
관심표준 등록 : 표준업데이트 시 알림서비스
제공형태 더보기-
표준
판매
ASTM F3478-20
Standard Practice for Development of a Durability and Reliability Flight Demonstration Program for Low-Risk Unmanned Aircraft Systems (UAS) under FAA Oversight- 발행일 : 2020-10-01
- 발행기관 : ASTM
상세정보
| 분야 | 15.09 : 종이, 회사 이미지용 상품 |
|---|---|
| 적용범위 | 1.1 This standard practice is intended for low-risk UAS seeking type certification by the Federal Aviation Administration (FAA) under 14 CFR Part 21.17(b) in accordance with the FAA durability and reliability (D&R) means of compliance (MOC). The definition of “low-risk UAS” does not necessarily align with other definitions found within corresponding ASTM standards (F3442/F3442M) or other UAS-related standards. For the purposes of this practice, “low-risk” is defined as a UAS operated in accordance with the concept of operations (CONOPs), eligibility criteria, and kinetic energy threshold specified in the G-1 Issue Paper (which will be provided to the applicant by the FAA). See 4.3 for design criteria and operating limitations for low-risk UAS. 1.2 This standard practice establishes a common methodology and key considerations for the development of minimum flight plans for low-risk UAS that demonstrate aircraft reliability as part of a D&R MOC. 1.3 The scope of this standard practice encompasses D&R planning, data collection, and reporting. 1.4 The values stated in SI units are to be regarded as standard. This is not intended to limit the systems of units used for design, development testing, or demonstration testing. However, the units of measurement used on pilot-facing placards and markings and manuals must be the same as those used on the corresponding equipment with recognition that international aviation utilizes feet for altitude and knots for airspeed as operational parameters. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | |
| 페이지수 | 22 |
| Edition | 20 |
이력정보
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM F3478-20상세보기 | Standard Practice for Development of a Durability and Reliability Flight Demonstration Program for Low-Risk Unmanned Aircraft Systems (UAS) under FAA Oversight | 2020-10-01 | 표준 |
관련상품
- 관련상품이 존재하지 않습니다.
다른 사람이 함께 구입한 상품
- ASTM F3548-21 - Standard Specification for UAS Traffic Management (UTM) UAS Service Supplier (USS) Interoperability
- ASTM F2851-10(2018) - Standard Practice for UAS Registration and Marking (Excluding Small Unmanned Aircraft Systems)
- ASTM F2908-23 - Standard Specification for Unmanned Aircraft Flight Manual (UFM) for an Unmanned Aircraft System (UAS)
- ASTM F3442/F3442M-23 - Standard Specification for Detect and Avoid System Performance Requirements
- ASTM F3341/F3341M-23 - Standard Terminology for Unmanned Aircraft Systems
추천 상품
- IEC TS 63134:2020 - Active assisted living (AAL) use cases
- IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification
- KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs)
- KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs)
- KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스
제공형태 닫기
PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)보안PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능PRINT :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)BOOK :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)ZIP :
압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)CD/DVD :
직접 파일 다운로드 및 인쇄(마이페이지 확인)DB :
별도 정보 제공HARDCOPY :
해외 배송 상품, 최대 3주 소요바인더 :
바인더 우편발송, 2~3일 소요온라인구독 :
WEB 접속 후 실시간 열람, 출력(1년간)