한국표준정보망

회원가입 로그인 비회원(주문조회) 장바구니 이용안내

English
메뉴
검색 마이페이지 장바구니0

QUICK

닫기

TOP

해외표준 상세정보

관심표준 등록 : 표준업데이트 시 알림서비스

제공형태 더보기

  • KS

    표준

    판매

    ASTM E606/E606M-21

    Standard Test Method for Strain-Controlled Fatigue Testing
    • 발행일 : 2021-06-01
    • 발행기관 : ASTM
    즐겨찾기 장바구니 담기
    닫기

    상품이 장바구니에 담겼습니다.

    장바구니로 이동

    • [영어]PDF 120,500원

    • [영어]PRINT 120,500원

상세정보

분야 03.01 : 금속-기계적 시험;가열 및 저온시험;금속 조직학
적용범위

1.1?This test method covers the determination of fatigue properties of nominally homogeneous materials by the use of test specimens subjected to uniaxial forces. It is intended as a guide for fatigue testing performed in support of such activities as materials research and development, mechanical design, process and quality control, product performance, and failure analysis. While this test method is intended primarily for strain-controlled fatigue testing, some sections may provide useful information for force-controlled or stress-controlled testing.

1.2?The use of this test method is limited to specimens and does not cover testing of full-scale components, structures, or consumer products.

1.3?This test method is applicable to temperatures and strain rates for which the magnitudes of time-dependent inelastic strains are on the same order or less than the magnitudes of time-independent inelastic strains. No restrictions are placed on environmental factors such as temperature, pressure, humidity, medium, and others, provided they are controlled throughout the test, do not cause loss of or change in dimension with time, and are detailed in the data report.

Note 1:?The term inelastic is used herein to refer to all nonelastic strains. The term plastic is used herein to refer only to the time-independent (that is, noncreep) component of inelastic strain. To truly determine a time-independent strain the force would have to be applied instantaneously, which is not possible. A useful engineering estimate of time-independent strain can be obtained when the strain rate exceeds some value. For example, a strain rate of 1?×?10?3 sec?1 is often used for this purpose. This value should increase with increasing test temperature.

1.4?This test method is restricted to the testing of uniform gage section test specimens subjected to axial forces as shown in Fig. 1(a). Testing is limited to strain-controlled cycling. The test method may be applied to hourglass specimens, see Fig. 1(b), but the user is cautioned about uncertainties in data analysis and interpretation. Testing is done primarily under constant amplitude cycling and may contain interspersed hold times at repeated intervals. The test method may be adapted to guide testing for more general cases where strain or temperature may vary according to application specific histories. Data analysis may not follow this test method in such cases.

FIG. 1?Recommended Low-Cycle Fatigue Specimens

Recommended Low-Cycle Fatigue SpecimensRecommended Low-Cycle Fatigue Specimens

Note 1:?*?Dimension d is recommended to be 6.35 mm [0.25 in.]. See 7.1. Centers permissible. **?This diameter may be made greater or less than 2d depending on material hardness. In typically ductile materials diameters less than 2d are often employed and in typically brittle materials diameters greater than 2d may be found desirable.

Note 2:?Threaded connections are more prone to inferior axial alignment and have greater potential for backlash, particularly if the connection with the grip is not properly designed.

1.5?The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.6?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
국제분류(ICS)코드 77.040.10 : 금속의 기계적 시험
페이지수 16
Edition 21

이력정보

No. 표준번호 표준명 발행일 상태
1 ASTM E606/E606M-21상세보기 Standard Test Method for Strain-Controlled Fatigue Testing 2021-06-01 표준
2 ASTM E606/E606M-21 REDLINE상세보기 Standard Test Method for Strain-Controlled Fatigue Testing 2021-06-01 표준
3 ASTM E606/E606M-19상세보기 Standard Test Method for Strain-Controlled Fatigue Testing 2019-11-01 구판
4 ASTM E606/E606M-19 REDLINE상세보기 Standard Test Method for Strain-Controlled Fatigue Testing 2019-11-01 구판
5 ASTM E606/E606M-19e1상세보기 Standard Test Method for Strain-Controlled Fatigue Testing 2019-11-01 구판
6 ASTM E606/E606M-12 REDLINE상세보기 Standard Test Method for Strain-Controlled Fatigue Testing 2012-06-01 구판
7 ASTM E606/E606M-12상세보기 Standard Test Method for Strain-Controlled Fatigue Testing 2012-06-01 구판

관련상품

  • 관련상품이 존재하지 않습니다.

다른 사람이 함께 구입한 상품

추천 상품

제공형태 닫기

  • PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)

  • 보안PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능

  • PRINT :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

  • BOOK :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

  • ZIP :

    압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)

  • CD/DVD :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)

  • DB :

    별도 정보 제공

  • HARDCOPY :

    해외 배송 상품, 최대 3주 소요

  • 바인더 :

    바인더 우편발송, 2~3일 소요

  • 온라인구독 :

    WEB 접속 후 실시간 열람, 출력(1년간)