한국표준정보망

회원가입 로그인 비회원(주문조회) 장바구니 이용안내

English
메뉴
검색 마이페이지 장바구니0

QUICK

닫기

TOP

해외표준 상세정보

관심표준 등록 : 표준업데이트 시 알림서비스

제공형태 더보기

  • KS

    구판

    판매

    ASTM F2620-20ae1

    Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings
    • 발행일 : 2020-12-01
    • 발행기관 : ASTM
    즐겨찾기 장바구니 담기
    닫기

    상품이 장바구니에 담겼습니다.

    장바구니로 이동

    • [영어]PDF 188,600원

    • [영어]PRINT 188,600원

상세정보

분야 08.04 : 플라스틱 파이프 및 건축용 제품
적용범위

1.1?This practice describes procedures for making joints with polyethylene (PE) pipe and fittings by means of heat fusion joining in, but not limited to, a field environment. Other suitable heat fusion joining procedures are available from various sources including pipe and fitting manufacturers. This practice does not purport to address all possible heat fusion joining procedures, or to preclude the use of qualified procedures developed by other parties that have been proved to produce reliable heat fusion joints.

1.2?The parameters and procedures are applicable only to joining polyethylene pipe and fittings of related polymer chemistry. They are intended for PE fuel gas pipe in accordance with Specification D2513 and PE potable water, sewer and industrial pipe manufactured in accordance with Specification F714, Specification D3035, and AWWA C901 and C906. Consult with the pipe manufacturers to make sure they approve this procedure for the pipe to be joined (see Appendix X1).

Note 1:?The parameters and procedures shown for Section 8. Procedure 2?Butt Fusion, were developed and validated using testing documented in Plastic Pipe Institute (PPI) TR-33. The parameters and procedures shown in Section 9. Procedure 3? Saddle Fusion, were developed and validated using testing documented in PPI TR-41.

Note 2:?Information about polyethylene pipe and fittings that have related polymer chemistry is presented in Plastics Pipe Institute (PPI) TR-33 and TR-41.

1.3?Parts that are within the dimensional tolerances given in present ASTM specifications are required to produce sound joints between polyethylene pipe and fittings when using the joining techniques described in this practice.

1.4?The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.5?The text of this practice references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the practice.

1.6?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.7?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
국제분류(ICS)코드 23.040.45 : 플라스틱 조립품
23.040.20 : 플라스틱 파이프
페이지수 22
Edition 20ae1

이력정보

No. 표준번호 표준명 발행일 상태
1 ASTM F2620-24상세보기 Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings 2024-07-01 표준
2 ASTM F2620-24 REDLINE상세보기 Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings 2024-07-01 표준
3 ASTM F2620-20ae2상세보기 Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings 2020-12-01 구판
4 ASTM F2620-20a상세보기 Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings 2020-12-01 구판
5 ASTM F2620-20ae1상세보기 Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings 2020-12-01 구판
6 ASTM F2620-20상세보기 Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings 2020-11-01 구판
7 ASTM F2620-19상세보기 Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings 2019-02-01 구판
8 ASTM F2620-19 REDLINE상세보기 Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings 2019-02-01 구판
9 ASTM F2620-13상세보기 Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings 2013-11-01 구판
10 ASTM F2620-13 REDLINE상세보기 Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings 2013-11-01 구판
11 ASTM F2620-12상세보기 Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings 2012-08-01 구판
12 ASTM F2620-11e1상세보기 Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings 2011-11-01 구판
13 ASTM F2620-11상세보기 Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings 2011-11-01 구판
14 ASTM F2620-09e1상세보기 Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings 2009-12-01 구판
15 ASTM F2620-09상세보기 Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings 2009-12-01 구판
16 ASTM F2620-06상세보기 Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings 2006-12-01 구판

관련상품

  • 관련상품이 존재하지 않습니다.

다른 사람이 함께 구입한 상품

  • 함께 구입한 상품이 존재하지 않습니다.

추천 상품

제공형태 닫기

  • PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)

  • 보안PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능

  • PRINT :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

  • BOOK :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

  • ZIP :

    압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)

  • CD/DVD :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)

  • DB :

    별도 정보 제공

  • HARDCOPY :

    해외 배송 상품, 최대 3주 소요

  • 바인더 :

    바인더 우편발송, 2~3일 소요

  • 온라인구독 :

    WEB 접속 후 실시간 열람, 출력(1년간)