사업자등록증
해외표준
FAQ
장바구니
고객센터
해외표준 상세정보
관심표준 등록 : 표준업데이트 시 알림서비스
제공형태 더보기-
구판
판매
ASTM F88/F88M-21
Standard Test Method for Seal Strength of Flexible Barrier Materials- 발행일 : 2021-11-15
- 발행기관 : ASTM
상세정보
| 분야 | 15.10 : 포장 |
|---|---|
| 적용범위 | 1.1?This test method covers the measurement of the strength of seals in flexible barrier materials. 1.2?The test may be conducted on seals between a flexible material and a rigid material. 1.3?Seals tested in accordance with this test method may be from any source, laboratory or commercial. 1.4?This test method measures the force required to separate a test strip of material containing the seal. It also identifies the mode of specimen failure. 1.5?This test method differs from Test Method F2824. Test Method F2824 measures mechanical seal strength while separating an entire lid (cover/membrane) from a rigid or semi-rigid round container. 1.6?This test method differs from Test Method F904. Test Method F904 measures the bond strength or ply adhesion of laminates made from flexible materials such as cellulose, paper, plastic film, and foil. 1.7?The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.8?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.9?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 55.040 : 포장 자재 및 부속품 |
| 페이지수 | 11 |
| Edition | 21 |
이력정보
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM F88/F88M-23상세보기 | Standard Test Method for Seal Strength of Flexible Barrier Materials | 2023-05-01 | 표준 |
| 2 | ASTM F88/F88M-23 REDLINE상세보기 | Standard Test Method for Seal Strength of Flexible Barrier Materials | 2023-05-01 | 표준 |
| 3 | ASTM F88/F88M-21상세보기 | Standard Test Method for Seal Strength of Flexible Barrier Materials | 2021-11-15 | 구판 |
| 4 | ASTM F88/F88M-21 REDLINE상세보기 | Standard Test Method for Seal Strength of Flexible Barrier Materials | 2021-11-15 | 구판 |
| 5 | ASTM F88/F88M-15 REDLINE상세보기 | Standard Test Method for Seal Strength of Flexible Barrier Materials | 2015-11-01 | 구판 |
| 6 | ASTM F88/F88M-15상세보기 | Standard Test Method for Seal Strength of Flexible Barrier Materials | 2015-11-01 | 구판 |
| 7 | ASTM F88/F88M-09상세보기 | Standard Test Method for Seal Strength of Flexible Barrier Materials | 2009-06-15 | 구판 |
관련상품
- 관련상품이 존재하지 않습니다.
다른 사람이 함께 구입한 상품
- ASTM F1980-21 - Standard Guide for Accelerated Aging of Sterile Barrier Systems and Medical Devices
- ISO 11138-1:2017 - Sterilization of health care products — Biological indicators — Part 1: General requirements
- ISO 13779-3:2018/Amd 1:2021 - Implants for surgery — Hydroxyapatite — Part 3: Chemical analysis and characterization of crystallinity ratio and phase purity — Amendment 1
- ISO 11138-7:2019 - Sterilization of health care products — Biological indicators — Part 7: Guidance for the selection, use and interpretation of results
- IEC 62366-1:2015 - Medical devices - Part 1: Application of usability engineering to medical devices
추천 상품
- IEC TS 63134:2020 - Active assisted living (AAL) use cases
- IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification
- KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs)
- KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs)
- KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스
제공형태 닫기
PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)보안PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능PRINT :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)BOOK :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)ZIP :
압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)CD/DVD :
직접 파일 다운로드 및 인쇄(마이페이지 확인)DB :
별도 정보 제공HARDCOPY :
해외 배송 상품, 최대 3주 소요바인더 :
바인더 우편발송, 2~3일 소요온라인구독 :
WEB 접속 후 실시간 열람, 출력(1년간)