한국표준정보망

회원가입 로그인 비회원(주문조회) 장바구니 이용안내

English
메뉴
검색 마이페이지 장바구니0

QUICK

닫기

TOP

해외표준 상세정보

관심표준 등록 : 표준업데이트 시 알림서비스

제공형태 더보기

  • KS

    표준

    판매

    ASTM D2166/D2166M-24

    Standard Test Method for Unconfined Compressive Strength of Cohesive Soil
    • 발행일 : 2024-06-01
    • 발행기관 : ASTM
    즐겨찾기 장바구니 담기
    닫기

    상품이 장바구니에 담겼습니다.

    장바구니로 이동

    • [영어]PDF 109,400원

    • [영어]PRINT 109,400원

상세정보

분야 04.08 : 토양, 석재 (Ⅰ)
적용범위

1.1?This test method covers the determination of the unconfined compressive strength of cohesive soil in the intact, remolded, or reconstituted condition, using strain-controlled application of the axial load.

1.2?This test method provides an approximate value of the strength of cohesive soils in terms of total stresses.

1.3?This test method is applicable only to cohesive materials which will not expel or bleed water (water expelled from the soil due to deformation) during the loading portion of the test and which will retain intrinsic strength after removal of confining pressures, such as clays or clayey soils. Dry and crumbly soils, fissured or varved materials, silts, peats, and sands cannot be tested with this method to obtain valid unconfined compressive strength values.

1.4?This test method is not a substitute for Test Method D2850.

Note 1:?The determination of the unconsolidated, undrained strength of cohesive soils with lateral confinement is covered by Test Method D2850. See 5.2 for additional information.

1.5?Units?The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Reporting of test results in units other than SI shall not be regarded as nonconformance with this standard.

1.5.1?The gravitational system of inch-pound units is used when dealing with inch-pound units. In this system, the pound (lbf) represents a unit of force (weight), while the unit for mass is slugs. The rationalized slug unit is not given, unless dynamic (F = ma) calculations are involved.

1.5.2?It is common practice in the engineering/construction profession to concurrently use pounds to represent both a unit of mass (lbm) and of force (lbf). This practice implicitly combines two separate systems of units; the absolute and the gravitational systems. It is scientifically undesirable to combine the use of two separate sets of inch-pound units within a single standard. As stated, this standard includes the gravitational system of inch-pound units and does not use/present the slug unit for mass. However, the use of balances or scales recording pounds of mass (lbm) or recording density in lbm/ft3 shall not be regarded as nonconformance with this standard.

1.6?All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026, unless superseded by this standard.

1.6.1?The procedures used to specify how data are collected/recorded or calculated in the standard are regarded as the industry standard. In addition, they are representative of the significant digits that generally should be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of this standard to consider significant digits used in analysis methods for engineering design.

1.7?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.8?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
국제분류(ICS)코드 93.020 : 토공. 굴착. 기초건설. 갱내작업
페이지수 8
Edition 24

이력정보

No. 표준번호 표준명 발행일 상태
1 ASTM D2166/D2166M-24상세보기 Standard Test Method for Unconfined Compressive Strength of Cohesive Soil 2024-06-01 표준
2 ASTM D2166/D2166M-24 REDLINE상세보기 Standard Test Method for Unconfined Compressive Strength of Cohesive Soil 2024-06-01 표준
3 ASTM D2166/D2166M-16 REDLINE상세보기 Standard Test Method for Unconfined Compressive Strength of Cohesive Soil 2016-07-01 구판
4 ASTM D2166/D2166M-16상세보기 Standard Test Method for Unconfined Compressive Strength of Cohesive Soil 2016-07-01 구판
5 ASTM D2166/D2166M-13상세보기 Standard Test Method for Unconfined Compressive Strength of Cohesive Soil 2013-05-15 구판

관련상품

  • 관련상품이 존재하지 않습니다.

다른 사람이 함께 구입한 상품

  • 함께 구입한 상품이 존재하지 않습니다.

추천 상품

제공형태 닫기

  • PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)

  • 보안PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능

  • PRINT :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

  • BOOK :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

  • ZIP :

    압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)

  • CD/DVD :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)

  • DB :

    별도 정보 제공

  • HARDCOPY :

    해외 배송 상품, 최대 3주 소요

  • 바인더 :

    바인더 우편발송, 2~3일 소요

  • 온라인구독 :

    WEB 접속 후 실시간 열람, 출력(1년간)