한국표준정보망

회원가입 로그인 비회원(주문조회) 장바구니0 이용안내

English

메뉴

한국표준정보망전체메뉴

세계 주요 표준,
빠르고 편리하게!

ENGLISH

검색 마이페이지 장바구니0

QUICK

닫기

TOP

해외표준 상세정보

관심표준 등록 : 표준업데이트 시 알림서비스

제공형태 더보기

표준

판매

ASTM E112-24

Standard Test Methods for Determining Average Grain Size
- 발행일 : 2024-04-01
- 발행기관 : ASTM
즐겨찾기 장바구니 담기

상품이 장바구니에 담겼습니다.
장바구니로 이동
- [영어]PDF 156,900원
- [영어]PRINT 156,900원

상세정보

분야

03.01 : 금속-기계적 시험;가열 및 저온시험;금속 조직학

적용범위

1.1?These test methods cover the measurement of average grain size and include the comparison procedure, the planimetric (or Jeffries) procedure, and the intercept procedures. These test methods may also be applied to nonmetallic materials with structures having appearances similar to those of the metallic structures shown in the comparison charts. These test methods apply chiefly to single phase grain structures but they can be applied to determine the average size of a particular type of grain structure in a multiphase or multiconstituent specimen.

1.2?These test methods are used to determine the average grain size of specimens with a unimodal distribution of grain areas, diameters, or intercept lengths. These distributions are approximately log normal. These test methods do not cover methods to characterize the nature of these distributions. Characterization of grain size in specimens with duplex grain size distributions is described in Test Methods E1181. Measurement of individual, very coarse grains in a fine grained matrix is described in Test Methods E930.

1.3?These test methods deal only with determination of planar grain size, that is, characterization of the two-dimensional grain sections revealed by the sectioning plane. Determination of spatial grain size, that is, measurement of the size of the three-dimensional grains in the specimen volume, is beyond the scope of these test methods.

1.4?These test methods describe techniques performed manually using either a standard series of graded chart images for the comparison method or simple templates for the manual counting methods. Utilization of semi-automatic digitizing tablets or automatic image analyzers to measure grain size is described in Test Methods E1382.

1.5?These test methods deal only with the recommended test methods and nothing in them should be construed as defining or establishing limits of acceptability or fitness of purpose of the materials tested.

1.6?The measured values are stated in SI units, which are regarded as standard. Equivalent inch-pound values, when listed, are in parentheses and may be approximate.

1.7?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.8?The paragraphs appear in the following order:

Section	Number
Scope	?1
Referenced Documents	?2
Terminology	?3
Significance and Use	?4
Generalities of Application	?5
Sampling	?6
Test Specimens	?7
Calibration	?8
Preparation of Photomicrographs	?9
Comparison Procedure	10
Planimetric (Jeffries) Procedure	11
General Intercept Procedures	12
Heyn Linear Intercept Procedure	13
Circular Intercept Procedures	14
Hilliard Single-Circle Procedure	?14.2
Abrams Three-Circle Procedure	?14.3
Statistical Analysis	15
Specimens with Non-equiaxed Grain Shapes	16
Specimens Containing Two or More Phases or Constituents	17
Report	18
Precision and Bias	19
Keywords	20
Annexes:	?
?Basis of ASTM Grain Size Numbers	Annex A1
?Equations for Conversions Among Various Grain Size Measurements	Annex A2
?Austenite Grain Size, Ferritic and Austenitic Steels	Annex A3
?Fracture Grain Size Method	Annex A4
?Requirements for Wrought Copper and Copper-Base Alloys	Annex A5
?Application to Special Situations	Annex A6
Appendixes:	?
?Results of Interlaboratory Grain Size Determinations	Appendix X1
?Referenced Adjuncts	Appendix X2

1.9?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

국제분류(ICS)코드

77.040.01 : 금속시험 일반

페이지수

Edition

이력정보

No.	표준번호	표준명	발행일	상태
1	ASTM E112-24상세보기	Standard Test Methods for Determining Average Grain Size	2024-04-01	표준
2	ASTM E112-24 REDLINE상세보기	Standard Test Methods for Determining Average Grain Size	2024-04-01	표준
3	ASTM E112-13(2021)상세보기	Standard Test Methods for Determining Average Grain Size	2021-09-01	구판
4	ASTM E112-13상세보기	Standard Test Methods for Determining Average Grain Size	2013-10-01	구판
5	ASTM E112-13 REDLINE상세보기	Standard Test Methods for Determining Average Grain Size	2013-10-01	구판
6	ASTM E112-12상세보기	Standard Test Methods for Determining Average Grain Size	2012-11-15	구판
7	ASTM E112-10상세보기	Standard Test Methods for Determining Average Grain Size	2010-11-01	구판
8	ASTM E112-96(2004)e2상세보기	Standard Test Methods for Determining Average Grain Size	2006-10-23	구판
9	ASTM E112-96(2004)e1상세보기	Standard Test Methods for Determining Average Grain Size	2004-11-01	구판
10	ASTM E112-96(2004)상세보기	Standard Test Methods for Determining Average Grain Size	2004-11-01	구판
11	ASTM E112-96e3상세보기	Standard Test Methods for Determining Average Grain Size	1996-01-01	구판
12	ASTM E112-96e2상세보기	Standard Test Methods for Determining Average Grain Size	1996-01-01	구판
13	ASTM E112-96e1상세보기	Standard Test Methods for Determining Average Grain Size	1996-01-01	구판
14	ASTM E112-88상세보기	Standard Test Methods for Determining Grain Size		구판