사업자등록증
해외표준
FAQ
장바구니
고객센터
해외표준 상세정보
관심표준 등록 : 표준업데이트 시 알림서비스
제공형태 더보기-
표준
판매
ASTM E111-17(2025)e1
Standard Test Method for Young’s Modulus, Tangent Modulus, and Chord Modulus- 발행일 : 2025-11-01
- 발행기관 : ASTM
상세정보
| 분야 | 03.01 : 금속-기계적 시험;가열 및 저온시험;금속 조직학 |
|---|---|
| 적용범위 | 1.1?This test method covers the determination of Young's modulus, tangent modulus, and chord modulus of structural materials, see Fig. 1. This test method is limited to materials, temperatures, and stresses at which creep is negligible compared to the strain produced immediately upon loading and to elastic behavior. |
1.2?Because of experimental problems associated with the establishment of the origin of the stress-strain curve described in 8.1, the determination of the initial tangent modulus (that is, the slope of the stress-strain curve at the origin) and the secant modulus are outside the scope of this test method.
1.3?The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
이력정보
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM E111-17(2025)e1상세보기 | Standard Test Method for Young’s Modulus, Tangent Modulus, and Chord Modulus | 2025-11-01 | 표준 |
| 2 | ASTM E111-17상세보기 | Standard Test Method for Young’s Modulus, Tangent Modulus, and Chord Modulus | 2017-07-15 | 구판 |
| 3 | ASTM E111-04(2010)상세보기 | Standard Test Method for Young's Modulus, Tangent Modulus, and Chord Modulus | 2010-09-15 | 구판 |
| 4 | ASTM E111-04상세보기 | Standard Test Method for Young's Modulus, Tangent Modulus, and Chord Modulus | 2004-06-01 | 구판 |
| 5 | ASTM E111-97상세보기 | Standard Test Method for Young's Modulus, Tangent Modulus, and Chord Modulus | 1997-04-10 | 구판 |
관련상품
- 관련상품이 존재하지 않습니다.
다른 사람이 함께 구입한 상품
- ASTM B881-25 - Standard Terminology Relating to Aluminum- and Magnesium-Alloy Products
- ASTM B247-25 - Standard Specification for Aluminum and Aluminum-Alloy Die Forgings, Hand Forgings, and Rolled Ring Forgings
- ASTM E6-25 - Standard Terminology Relating to Methods of Mechanical Testing
- ASTM E1251-25 - Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Spark Atomic Emission Spectrometry
- ASTM E18-25 - Standard Test Methods for Rockwell Hardness of Metallic Materials
추천 상품
- IEC TS 63134:2020 - Active assisted living (AAL) use cases
- IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification
- KS B ISO/TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs)
- KS B ISO/TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs)
- KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스