사업자등록증
해외표준
FAQ
장바구니
고객센터
해외표준 상세정보
관심표준 등록 : 표준업데이트 시 알림서비스
제공형태 더보기-
구판
판매
ASTM F1545-15a REDLINE
Standard Specification for Plastic-Lined Ferrous Metal Pipe, Fittings, and Flanges- 발행일 : 2015-05-01
- 발행기관 : ASTM
-
레드라인이란?
최신표준과 직전 구판표준의 변경내용을 포함하고 있는 버전. 구입 시 최신표준과 레드라인 두 개 파일을 제공합니다.
상세정보
| 분야 | |
|---|---|
| 적용범위 | 1.1 This specification covers factory-made plastic-lined ferrous metal pipe, fittings, and flanges intended primarily for conveying corrosive fluids. Requirements for materials, workmanship, dimensions, design, fabrication, working pressure and temperatures, test methods, qualification requirements, and markings are included. 1.1.1 This specification does not define the suitability of different liner materials to various chemical and operating environments. Refer to the manufacturer's chemical resistance data for suitability recommendations. 1.1.2 This specification does not include products coated with plastics. 1.2 This specification covers plastic-lined pipe, flanges, and fittings as listed in Table 1. Pressure limitations shall be in accordance with ASME B16 Standards, except reduced pressure limitations may be established by the manufacturer, considering both pressure and temperature limitations of the ferrous metal housing and the sealing ability of the liner. Note 1: In this specification, propylene plastics cover those materials defined as both polypropylene plastics and propylene plastics in Terminology F412. Both materials are identified as “PP” on the product. Note that this is at variance with Terminology D1600, where “PP” is the abbreviation for polypropylene. 1.3 The plastic-lined flanged pipe and fitting assemblies are limited to temperatures shown in Table 2. End users should consult with manufacturers as to the likely result of using a particular lined piping component at temperatures below the rated minimum. Note 2: The temperature limitations are based on noncorrosive test conditions. Use in specific aggressive environments may alter temperature limitations. In such instances, specific temperature limits shall be established by mutual agreement between the purchaser and the manufacturer. (A) Storage or handling below 20°F (−7°C) of uninstalled 4, 6, and 8-in. components should be avoided. Check flange face ‘cold-flow’ modulus, and check chemical compatibility at all expected operating temperatures 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
| 국제분류(ICS)코드 | |
| 페이지수 | 9 |
| Edition | 15a |
이력정보
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM F1545-15a(2021)상세보기 | Standard Specification for Plastic-Lined Ferrous Metal Pipe, Fittings, and Flanges | 2021-07-01 | 표준 |
| 2 | ASTM F1545-15a상세보기 | Standard Specification for Plastic-Lined Ferrous Metal Pipe, Fittings, and Flanges | 2015-05-01 | 구판 |
| 3 | ASTM F1545-15a REDLINE상세보기 | Standard Specification for Plastic-Lined Ferrous Metal Pipe, Fittings, and Flanges | 2015-05-01 | 구판 |
| 4 | ASTM F1545-15상세보기 | Standard Specification for Plastic-Lined Ferrous Metal Pipe, Fittings, and Flanges | 2015-03-15 | 구판 |
| 5 | ASTM F1545-97(2009)상세보기 | Standard Specification for Plastic-Lined Ferrous Metal Pipe, Fittings, and Flanges | 2009-08-01 | 구판 |
| 6 | ASTM F1545-97(2003)상세보기 | Standard Specification for Plastic-Lined Ferrous Metal Pipe, Fittings, and Flanges | 2003-08-10 | 구판 |
| 7 | ASTM F1545-97상세보기 | Standard Specification for Plastic-Lined Ferrous Metal Pipe, Fittings, and Flanges | 1997-11-10 | 구판 |
| 8 | ASTM F1545-97e1상세보기 | Standard Specification for Plastic-Lined Ferrous Metal Pipe, Fittings, and Flanges | 1997-11-10 | 구판 |
관련상품
- 관련상품이 존재하지 않습니다.
다른 사람이 함께 구입한 상품
- ISO 11414:2009 - Plastics pipes and fittings — Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion
- KS C IEC 60079-10-1 - 폭발 분위기－제10-1부：폭발위험 장소의 구분
- ISO 3213:2009 - Polypropylene (PP) pipes — Effect of time and temperature on the expected strength
- ASME STP-PT-006-2007 - Design Guidelines for Hydrogen Piping and Pipelines (STP-PT-006 - 2007)
- ISO 15494:2015 - Plastics piping systems for industrial applications — Polybutene (PB), polyethylene (PE), polyethylene of raised temperature resistance (PE-RT), crosslinked polyethylene (PE-X), polypropylene (PP) — Metric series for specifications for components and the system
추천 상품
- IEC TS 63134:2020 - Active assisted living (AAL) use cases
- IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification
- KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs)
- KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs)
- KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스
제공형태 닫기
PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)보안PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능PRINT :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)BOOK :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)ZIP :
압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)CD/DVD :
직접 파일 다운로드 및 인쇄(마이페이지 확인)DB :
별도 정보 제공HARDCOPY :
해외 배송 상품, 최대 3주 소요바인더 :
바인더 우편발송, 2~3일 소요온라인구독 :
WEB 접속 후 실시간 열람, 출력(1년간)