사업자등록증
해외표준
FAQ
장바구니
고객센터
해외표준 상세정보
관심표준 등록 : 표준업데이트 시 알림서비스
제공형태 더보기-
구판
판매
ASTM G99-17 REDLINE
Standard Test Method for Wear Testing with a Pin-on-Disk Apparatus- 발행일 : 2017-01-01
- 발행기관 : ASTM
-
레드라인이란?
최신표준과 직전 구판표준의 변경내용을 포함하고 있는 버전. 구입 시 최신표준과 레드라인 두 개 파일을 제공합니다.
상세정보
| 분야 | |
|---|---|
| 적용범위 | 1.1 This test method covers a laboratory procedure for determining the wear of materials during sliding using a pin-on-disk apparatus. Materials are tested in pairs under nominally non-abrasive conditions. The principal areas of experimental attention in using this type of apparatus to measure wear are described. The coefficient of friction may also be determined. 1.2 This test method standard uses a specific set of test parameters (load, sliding speed, materials, etc.) that were then used in an interlaboratory study (ILS), the results of which are given here (Tables 1 and 2). (This satisfies the ASTM form in that “The directions for performing the test should include all of the essential details as to apparatus, test specimen, procedure, and calculations needed to achieve satisfactory precision and bias.”) Any user should report that they “followed the requirements of ASTM G99,” where that is true. 1.3 Now it is often found in practice that users may follow all instructions given here, but choose other test parameters, such as load, speed, materials, environment, etc., and thereby obtain different test results. Such a use of this standard is encouraged as a means to improve wear testing methodology. However, it must be clearly stated in any report that, while the directions and protocol in Test Method G99 were followed (if true), the choices of test parameters were different from Test Method G99 values, and the test results were therefore also different from the Test Method G99 results. This use should be described as having “followed the procedure of ASTM G99.” All test parameters that were used in such case must be stated. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
| 국제분류(ICS)코드 | |
| 페이지수 | 6 |
| Edition | 17 |
이력정보
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM G99-23상세보기 | Standard Test Method for Wear and Friction Testing with a Pin-on-Disk or Ball-on-Disk Apparatus | 2023-11-01 | 표준 |
| 2 | ASTM G99-23 REDLINE상세보기 | Standard Test Method for Wear and Friction Testing with a Pin-on-Disk or Ball-on-Disk Apparatus | 2023-11-01 | 표준 |
| 3 | ASTM G99-17 REDLINE상세보기 | Standard Test Method for Wear Testing with a Pin-on-Disk Apparatus | 2017-01-01 | 구판 |
| 4 | ASTM G99-17상세보기 | Standard Test Method for Wear Testing with a Pin-on-Disk Apparatus | 2017-01-01 | 구판 |
| 5 | ASTM G99-05(2016)상세보기 | Standard Test Method for Wear Testing with a Pin-on-Disk Apparatus | 2016-06-01 | 구판 |
| 6 | ASTM G99-05(2010)상세보기 | Standard Test Method for Wear Testing with a Pin-on-Disk Apparatus | 2010-04-01 | 구판 |
| 7 | ASTM G99-05상세보기 | Standard Test Method for Wear Testing with a Pin-on-Disk Apparatus | 2005-05-01 | 구판 |
| 8 | ASTM G99-04a상세보기 | Standard Test Method for Wear Testing with a Pin-on-Disk Apparatus | 2004-11-01 | 구판 |
| 9 | ASTM G99-04상세보기 | Standard Test Method for Wear Testing with a Pin-on-Disk Apparatus | 2004-01-01 | 구판 |
| 10 | ASTM G99-03상세보기 | Standard Test Method for Wear Testing with a Pin-on-Disk Apparatus | 2003-05-10 | 구판 |
| 11 | ASTM G99-95a(2000)e1상세보기 | Standard Test Method for Wear Testing with a Pin-on-Disk Apparatus | 2000-05-10 | 구판 |
관련상품
- 관련상품이 존재하지 않습니다.
다른 사람이 함께 구입한 상품
추천 상품
- IEC TS 63134:2020 - Active assisted living (AAL) use cases
- IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification
- KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs)
- KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs)
- KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스
제공형태 닫기
PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)보안PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능PRINT :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)BOOK :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)ZIP :
압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)CD/DVD :
직접 파일 다운로드 및 인쇄(마이페이지 확인)DB :
별도 정보 제공HARDCOPY :
해외 배송 상품, 최대 3주 소요바인더 :
바인더 우편발송, 2~3일 소요온라인구독 :
WEB 접속 후 실시간 열람, 출력(1년간)