한국표준정보망

회원가입 로그인 비회원(주문조회) 장바구니0 이용안내

English

메뉴

한국표준정보망전체메뉴

세계 주요 표준,
빠르고 편리하게!

ENGLISH

검색 마이페이지 장바구니0

QUICK

닫기

TOP

해외표준 상세정보

관심표준 등록 : 표준업데이트 시 알림서비스

제공형태 더보기

구판

판매

ASTM E262-17 REDLINE

Standard Test Method for Determining Thermal Neutron Reaction Rates and Thermal Neutron Fluence Rates by Radioactivation Techniques
- 발행일 : 2017-08-01
- 발행기관 : ASTM
즐겨찾기 장바구니 담기

상품이 장바구니에 담겼습니다.
장바구니로 이동
- [영어]PDF(레드라인) 144,300원
- [영어]PRINT(레드라인) 144,300원
레드라인이란?

최신표준과 직전 구판표준의 변경내용을 포함하고 있는 버전. 구입 시 최신표준과 레드라인 두 개 파일을 제공합니다.

상세정보

분야

적용범위

1.1 The purpose of this test method is to define a general procedure for determining an unknown thermal-neutron fluence rate by neutron activation techniques. It is not practicable to describe completely a technique applicable to the large number of experimental situations that require the measurement of a thermal-neutron fluence rate. Therefore, this method is presented so that the user may adapt to their particular situation the fundamental procedures of the following techniques.

1.1.1 Radiometric counting technique using pure cobalt, pure gold, pure indium, cobalt-aluminum, alloy, gold-aluminum alloy, or indium-aluminum alloy.

1.1.2 Standard comparison technique using pure gold, or gold-aluminum alloy, and

1.1.3 Secondary standard comparison techniques using pure indium, indium-aluminum alloy, pure dysprosium, or dysprosium-aluminum alloy.

1.2 The techniques presented are limited to measurements at room temperatures. However, special problems when making thermal-neutron fluence rate measurements in high-temperature environments are discussed in 9.2. For those circumstances where the use of cadmium as a thermal shield is undesirable because of potential spectrum perturbations or of temperatures above the melting point of cadmium, the method described in Test Method E481 can be used in some cases. Alternatively, gadolinium filters may be used instead of cadmium. For high temperature applications in which aluminum alloys are unsuitable, other alloys such as cobalt-nickel or cobalt-vanadium have been used.

1.3 This test method may be used to determine the equivalent 2200 m/s fluence rate. The accurate determination of the actual thermal neutron fluence rate requires knowledge of the neutron temperature, and determination of the neutron temperature is not within the scope of the standard.

1.4 The techniques presented are suitable only for neutron fields having a significant thermal neutron component, in which moderating materials are present, and for which the average scattering cross section is large compared to the average absorption cross section in the thermal neutron energy range.

1.5 Table 1 indicates the useful neutron-fluence ranges for each detector material.

TABLE 1 Useful Neutron Fluence Ranges of Foil Material

Foil Material	Form	≈ Useful Range (neutrons/cm²)
Indium	pure or alloyed with aluminum	10³ to 10¹²
Gold	pure or alloyed with aluminum	10⁷ to 10¹⁴
Dysprosium	pure or alloyed with aluminum	10³ to 10¹⁰
Cobalt	pure or alloyed with aluminum	10¹⁴ to 10²⁰

1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health and environmental practices and determine the applicability of regulatory limitations prior to use.

1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

국제분류(ICS)코드

페이지수

Edition

이력정보

No.	표준번호	표준명	발행일	상태
1	ASTM E262-17(2024)e1상세보기	Standard Test Method for Determining Thermal Neutron Reaction Rates and Thermal Neutron Fluence Rates by Radioactivation Techniques	2024-05-01	표준
2	ASTM E262-17상세보기	Standard Test Method for Determining Thermal Neutron Reaction Rates and Thermal Neutron Fluence Rates by Radioactivation Techniques	2017-08-01	구판
3	ASTM E262-17 REDLINE상세보기	Standard Test Method for Determining Thermal Neutron Reaction Rates and Thermal Neutron Fluence Rates by Radioactivation Techniques	2017-08-01	구판
4	ASTM E262-13상세보기	Standard Test Method for Determining Thermal Neutron Reaction Rates and Thermal Neutron Fluence Rates by Radioactivation Techniques	2013-01-01	구판
5	ASTM E262-08상세보기	Standard Test Method for Determining Thermal Neutron Reaction Rates and Thermal Neutron Fluence Rates by Radioactivation Techniques	2008-11-01	구판
6	ASTM E262-03상세보기	Standard Method for Determining Thermal Neutron Reaction and Fluence Rates by Radioactivation Techniques	2003-02-10	구판
7	ASTM E262-97상세보기	Standard Method for Determining Thermal Neutron Reaction and Fluence Rates by Radioactivation Techniques	1997-06-10	구판