사업자등록증
해외표준
FAQ
장바구니
고객센터
해외표준 상세정보
관심표준 등록 : 표준업데이트 시 알림서비스
제공형태 더보기-
구판
판매
ASTM C1525-18 REDLINE
Standard Test Method for Determination of Thermal Shock Resistance for Advanced Ceramics by Water Quenching- 발행일 : 2018-07-01
- 발행기관 : ASTM
-
레드라인이란?
최신표준과 직전 구판표준의 변경내용을 포함하고 있는 버전. 구입 시 최신표준과 레드라인 두 개 파일을 제공합니다.
상세정보
| 분야 | |
|---|---|
| 적용범위 | 1.1 This test method describes the determination of the resistance of advanced ceramics to thermal shock by water quenching. The method builds on the experimental principle of rapid quenching of a test specimen at an elevated temperature in a water bath at room temperature. The effect of the thermal shock is assessed by measuring the reduction in flexural strength produced by rapid quenching of test specimens heated across a range of temperatures. For a quantitative measurement of thermal shock resistance, a critical temperature interval is determined by a reduction in the mean flexural strength of at least 30 %. The test method does not determine thermal stresses developed as a result of a steady-state temperature difference within a ceramic body or of thermal expansion mismatch between joined bodies. The test method is not intended to determine the resistance of a ceramic material to repeated shocks. Since the determination of the thermal shock resistance is performed by evaluating retained strength, the method is not suitable for ceramic components; however, test specimens cut from components may be used. 1.2 The test method is intended primarily for dense monolithic ceramics, but may also be applicable to certain composites such as whisker- or particulate-reinforced ceramic matrix composites that are macroscopically homogeneous. 1.3 Values expressed in this standard test method are in accordance with the International System of Units (SI) and IEEE/ASTM SI 10. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | |
| 페이지수 | 8 |
| Edition | 18 |
이력정보
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM C1525-18(2024)상세보기 | Standard Test Method for Determination of Thermal Shock Resistance for Advanced Ceramics by Water Quenching | 2024-09-01 | 표준 |
| 2 | ASTM C1525-18 REDLINE상세보기 | Standard Test Method for Determination of Thermal Shock Resistance for Advanced Ceramics by Water Quenching | 2018-07-01 | 구판 |
| 3 | ASTM C1525-04(2013)상세보기 | Standard Test Method for Determination of Thermal Shock Resistance for Advanced Ceramics by Water Quenching | 2013-08-01 | 구판 |
| 4 | ASTM C1525-04(2009)상세보기 | Standard Test Method for Determination of Thermal Shock Resistance for Advanced Ceramics by Water Quenching | 2009-07-01 | 구판 |
| 5 | ASTM C1525-04상세보기 | Standard Test Method for Determination of Thermal Shock Resistance for Advanced Ceramics by Water Quenching | 2004-05-01 | 구판 |
| 6 | ASTM C1525-03상세보기 | Standard Test Method for Determination of Thermal Shock Resistance for Advanced Ceramics by Water Quenching | 2003-05-10 | 구판 |
| 7 | ASTM C1525-02상세보기 | Standard Test Method for Determination of Thermal Shock Resistance for Advanced Ceramics by Water Quenching | 2002-04-10 | 구판 |
관련상품
- 관련상품이 존재하지 않습니다.
다른 사람이 함께 구입한 상품
- ASTM E2109-01(2014) - Standard Test Methods for Determining Area Percentage Porosity in Thermal Sprayed Coatings
- ASTM C1421-18 REDLINE - Standard Test Methods for Determination of Fracture Toughness of Advanced Ceramics at Ambient Temperature
- ASTM C1211-18 REDLINE - Standard Test Method for Flexural Strength of Advanced Ceramics at Elevated Temperatures
추천 상품
- IEC TS 63134:2020 - Active assisted living (AAL) use cases
- IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification
- KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs)
- KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs)
- KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스
제공형태 닫기
PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)보안PDF :
직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능PRINT :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)BOOK :
인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)ZIP :
압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)CD/DVD :
직접 파일 다운로드 및 인쇄(마이페이지 확인)DB :
별도 정보 제공HARDCOPY :
해외 배송 상품, 최대 3주 소요바인더 :
바인더 우편발송, 2~3일 소요온라인구독 :
WEB 접속 후 실시간 열람, 출력(1년간)