한국표준정보망

회원가입 로그인 비회원(주문조회) 장바구니 이용안내

English
메뉴
검색 마이페이지 장바구니0

QUICK

닫기

TOP

해외표준 상세정보

관심표준 등록 : 표준업데이트 시 알림서비스

제공형태 더보기

  • KS

    구판

    판매

    ASTM E2579-19 REDLINE

    Standard Practice for Specimen Preparation and Mounting of Wood Products to Assess Surface Burning Characteristics
    • 발행일 : 2019-04-01
    • 발행기관 : ASTM
    즐겨찾기 장바구니 담기
    닫기

    상품이 장바구니에 담겼습니다.

    장바구니로 이동

    • [영어]PDF(레드라인) 131,600원

    • [영어]PRINT(레드라인) 131,600원

  • 레드라인이란?

    최신표준과 직전 구판표준의 변경내용을 포함하고 있는 버전. 구입 시 최신표준과 레드라인 두 개 파일을 제공합니다.

상세정보

분야
적용범위

1.1 This practice describes procedures for specimen preparation and mounting when testing wood products to assess flames spread and smoke development as surface burning characteristics using Test Method E84.

1.2 This practice applies also to laminated products factory-produced with a wood substrate (see 8.6). This practice does not apply to wood veneers or facings intended to be applied on site over a wood substrate, which are covered by Practice E2404.

1.3 Testing is conducted with Test Method E84.

1.4 Testing for the reporting of the moisture content of the test specimen is conducted with Test Methods D4442.

1.5 This practice does not provide pass/fail criteria that can be used as a regulatory tool.

1.6 Use the values stated in inch-pound units as the standard, in referee decisions. The values in the SI system of units are given in parentheses, for information only; see IEEE/ASTM SI-10 for further details.

1.7 This fire standard cannot be used to provide quantitative measures.

1.8 Fire testing of products and materials is inherently hazardous, and adequate safeguards for personnel and property shall be employed in conducting these tests. Fire testing involves hazardous materials and equipment. This standard gives instructions on specimen preparation and mounting, but the fire-test-response method is given in Test Method E84. See also Section 10.

1.9 The text of this standard references notes and footnotes which provide explanatory materials. These notes and footnotes shall not be considered requirements of the standard.

1.10 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.11 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
국제분류(ICS)코드
페이지수 5
Edition 19

이력정보

No. 표준번호 표준명 발행일 상태
1 ASTM E2579-23b상세보기 Standard Practice for Specimen Preparation and Mounting of Wood Products to Assess Surface Burning Characteristics 2023-11-01 표준
2 ASTM E2579-23b REDLINE상세보기 Standard Practice for Specimen Preparation and Mounting of Wood Products to Assess Surface Burning Characteristics 2023-11-01 표준
3 ASTM E2579-23a상세보기 Standard Practice for Specimen Preparation and Mounting of Wood Products to Assess Surface Burning Characteristics 2023-03-01 구판
4 ASTM E2579-23a REDLINE상세보기 Standard Practice for Specimen Preparation and Mounting of Wood Products to Assess Surface Burning Characteristics 2023-03-01 구판
5 ASTM E2579-23상세보기 Standard Practice for Specimen Preparation and Mounting of Wood Products to Assess Surface Burning Characteristics 2023-02-01 구판
6 ASTM E2579-23 REDLINE상세보기 Standard Practice for Specimen Preparation and Mounting of Wood Products to Assess Surface Burning Characteristics 2023-02-01 구판
7 ASTM E2579-21 REDLINE상세보기 Standard Practice for Specimen Preparation and Mounting of Wood Products to Assess Surface Burning Characteristics 2021-08-01 구판
8 ASTM E2579-21상세보기 Standard Practice for Specimen Preparation and Mounting of Wood Products to Assess Surface Burning Characteristics 2021-08-01 구판
9 ASTM E2579-20상세보기 Standard Practice for Specimen Preparation and Mounting of Wood Products to Assess Surface Burning Characteristics 2020-12-15 구판
10 ASTM E2579-20 REDLINE상세보기 Standard Practice for Specimen Preparation and Mounting of Wood Products to Assess Surface Burning Characteristics 2020-12-15 구판
11 ASTM E2579-19상세보기 Standard Practice for Specimen Preparation and Mounting of Wood Products to Assess Surface Burning Characteristics 2019-04-01 구판
12 ASTM E2579-19 REDLINE상세보기 Standard Practice for Specimen Preparation and Mounting of Wood Products to Assess Surface Burning Characteristics 2019-04-01 구판
13 ASTM E2579-15 REDLINE상세보기 Standard Practice for Specimen Preparation and Mounting of Wood Products to Assess Surface Burning Characteristics 2015-04-01 구판
14 ASTM E2579-15상세보기 Standard Practice for Specimen Preparation and Mounting of Wood Products to Assess Surface Burning Characteristics 2015-04-01 구판
15 ASTM E2579-13상세보기 Standard Practice for Specimen Preparation and Mounting of Wood Products to Assess Surface Burning Characteristics 2013-04-01 구판
16 ASTM E2579-12상세보기 Standard Practice for Specimen Preparation and Mounting of Wood Products to Assess Surface Burning Characteristics 2012-12-15 구판
17 ASTM E2579-11상세보기 Standard Practice for Specimen Preparation and Mounting of Wood Products to Assess Surface Burning Characteristics 2011-10-01 구판
18 ASTM E2579-07상세보기 Standard Practice for Specimen Preparation and Mounting of Wood Products to Assess Surface Burning Characteristics 2007-10-01 구판

관련상품

  • 관련상품이 존재하지 않습니다.

다른 사람이 함께 구입한 상품

추천 상품

제공형태 닫기

  • PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)

  • 보안PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능

  • PRINT :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

  • BOOK :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

  • ZIP :

    압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)

  • CD/DVD :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)

  • DB :

    별도 정보 제공

  • HARDCOPY :

    해외 배송 상품, 최대 3주 소요

  • 바인더 :

    바인더 우편발송, 2~3일 소요

  • 온라인구독 :

    WEB 접속 후 실시간 열람, 출력(1년간)