한국표준정보망

회원가입 로그인 비회원(주문조회) 장바구니 이용안내

English
메뉴
검색 마이페이지 장바구니0

QUICK

닫기

TOP

해외표준 상세정보

관심표준 등록 : 표준업데이트 시 알림서비스

제공형태 더보기

  • KS

    구판

    판매

    ASTM D3801-20 REDLINE

    Standard Test Method for Measuring the Comparative Burning Characteristics of Solid Plastics in a Vertical Position
    • 발행일 : 2020-02-01
    • 발행기관 : ASTM
    즐겨찾기 장바구니 담기
    닫기

    상품이 장바구니에 담겼습니다.

    장바구니로 이동

    • [영어]PDF(레드라인) 131,600원

    • [영어]PRINT(레드라인) 131,600원

  • 레드라인이란?

    최신표준과 직전 구판표준의 변경내용을 포함하고 있는 버전. 구입 시 최신표준과 레드라인 두 개 파일을 제공합니다.

상세정보

분야
적용범위

1.1 This fire-test-response standard covers a small-scale laboratory procedure for determining comparative burning characteristics of solid-plastic material, using a 20-mm (50W) premixed flame applied to the base of specimens held in a vertical position.

Note 1: This test method and the 20 mm (50W) Vertical Burning Test (V-0, V-1, or V-2) of ANSI/UL 94 are equivalent.

Note 2: This test method and Test Method B of IEC 60695–11–10 are equivalent. IEC 60695–11–10 has replaced ISO 1210.

Note 3: For additional information on materials that burn up to the holding clamp by this test method, see Test Method D635. For test methods of flexible plastics in the form of thin sheets and film, see Test Method D4804. For additional information on comparative burning characteristics and resistance to burn-through, see Test Method D5048.

1.2 This test method was developed for polymeric materials used for parts in devices and appliances. The results are intended to serve as a preliminary indication of their acceptability with respect to flammability for a particular application. The final acceptance of the material is dependent upon its use in complete equipment that conforms with the standards applicable to such equipment.

1.3 The classification system described in the appendix is intended for quality assurance and the preselection of component materials for products.

1.4 It is possible that this test is applicable to nonmetallic materials other than plastics. Such application is outside the scope of this technical committee.

1.5 This test method does not cover plastics when used for building construction, finishing or contents such as wall and floor coverings, furnishings, decorative objects etc. In addition, the fire resistance (in terms of an hourly rating), flame spread, smoke characterization and heat release rate are not evaluated by this test. Other fire tests exist and shall be used to evaluate the flammability of materials in these intended end use product configuration.

1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.7 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions.

1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
국제분류(ICS)코드
페이지수 7
Edition 20

이력정보

No. 표준번호 표준명 발행일 상태
1 ASTM D3801-20a상세보기 Standard Test Method for Measuring the Comparative Burning Characteristics of Solid Plastics in a Vertical Position 2020-09-01 표준
2 ASTM D3801-20a REDLINE상세보기 Standard Test Method for Measuring the Comparative Burning Characteristics of Solid Plastics in a Vertical Position 2020-09-01 표준
3 ASTM D3801-20상세보기 Standard Test Method for Measuring the Comparative Burning Characteristics of Solid Plastics in a Vertical Position 2020-02-01 구판
4 ASTM D3801-20 REDLINE상세보기 Standard Test Method for Measuring the Comparative Burning Characteristics of Solid Plastics in a Vertical Position 2020-02-01 구판
5 ASTM D3801-19a상세보기 Standard Test Method for Measuring the Comparative Burning Characteristics of Solid Plastics in a Vertical Position 2019-12-01 구판
6 ASTM D3801-19a REDLINE상세보기 Standard Test Method for Measuring the Comparative Burning Characteristics of Solid Plastics in a Vertical Position 2019-12-01 구판
7 ASTM D3801-19상세보기 Standard Test Method for Measuring the Comparative Burning Characteristics of Solid Plastics in a Vertical Position 2019-01-15 구판
8 ASTM D3801-10 REDLINE상세보기 Standard Test Method for Measuring the Comparative Burning Characteristics of Solid Plastics in a Vertical Position 2010-07-01 표준
9 ASTM D3801-10상세보기 Standard Test Method for Measuring the Comparative Burning Characteristics of Solid Plastics in a Vertical Position 2010-07-01 표준
10 ASTM D3801-06상세보기 Standard Test Method for Measuring the Comparative Burning Characteristics of Solid Plastics in a Vertical Position 2006-09-15 구판
11 ASTM D3801-96e1상세보기 Standard Test Method for Measuring the Comparative Burning Characteristics of Solid Plastics in a Vertical Position 2000-12-10 구판
12 ASTM D3801-00상세보기 Standard Test Method for Measuring the Comparative Burning Characteristics of Solid Plastics in a Vertical Position 2000-12-10 구판

관련상품

  • 관련상품이 존재하지 않습니다.

다른 사람이 함께 구입한 상품

  • 함께 구입한 상품이 존재하지 않습니다.

추천 상품

제공형태 닫기

  • PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)

  • 보안PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능

  • PRINT :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

  • BOOK :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

  • ZIP :

    압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)

  • CD/DVD :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)

  • DB :

    별도 정보 제공

  • HARDCOPY :

    해외 배송 상품, 최대 3주 소요

  • 바인더 :

    바인더 우편발송, 2~3일 소요

  • 온라인구독 :

    WEB 접속 후 실시간 열람, 출력(1년간)