QUICK

TOP

해외표준 상세정보

관심표준 등록 : 표준업데이트 시 알림서비스

제공형태 더보기
  • KS

    표준

    판매

    ASTM E92-23 REDLINE

    Standard Test Methods for Vickers Hardness and Knoop Hardness of Metallic Materials
    • 발행일 : 2023-07-01
    • 발행기관 : ASTM
    즐겨찾기 장바구니 담기
    닫기

    상품이 장바구니에 담겼습니다.

    장바구니로 이동
    • [영어]PDF(레드라인) 192,000원

    • [영어]PRINT(레드라인) 192,000원

  • 레드라인이란?

    최신표준과 직전 구판표준의 변경내용을 포함하고 있는 버전. 구입 시 최신표준과 레드라인 두 개 파일을 제공합니다.

상세정보

분야
적용범위

1.1?These test methods cover the determination of the Vickers hardness and Knoop hardness of metallic materials by the Vickers and Knoop indentation hardness principles. This standard provides the requirements for Vickers and Knoop hardness machines and the procedures for performing Vickers and Knoop hardness tests.

1.2?This standard includes additional requirements in annexes:

Verification of Vickers and Knoop Hardness Testing Machines

Annex A1

Vickers and Knoop Hardness Standardizing Machines

Annex A2

Standardization of Vickers and Knoop Indenters

Annex A3

Standardization of Vickers and Knoop Hardness Test Blocks

Annex A4

Correction Factors for Vickers Hardness Tests Made on Spherical and Cylindrical Surfaces

Annex A5

1.3?This standard includes nonmandatory information in an appendix which relates to the Vickers and Knoop hardness tests:

Examples of Procedures for Determining Vickers and Knoop Hardness Uncertainty

Appendix X1

1.4?This test method covers Vickers hardness tests made utilizing test forces ranging from 9.807 × 10-3 N to 1176.80 N (1 gf to 120 kgf), and Knoop hardness tests made utilizing test forces from 9.807 × 10-3 N to 19.613 N (1 gf to 2 kgf).

1.5?Additional information on the procedures and guidance when testing in the microindentation force range (forces 1 kgf) may be found in Test Method E384, Test Method for Microindentation Hardness of Materials.

1.6?Units?When the Vickers and Knoop hardness tests were developed, the force levels were specified in units of grams-force (gf) and kilograms-force (kgf). This standard specifies the units of force and length in the International System of Units (SI); that is, force in Newtons (N) and length in mm or ?m. However, because of the historical precedent and continued common usage, force values in gf and kgf units are provided for information and much of the discussion in this standard as well as the method of reporting the test results refers to these units.

Note 1:?The Vickers and Knoop hardness numbers were originally defined in terms of the test force in kilogram-force (kgf) and the surface area or projected area in millimetres squared (mm2). Today, the hardness numbers are internationally defined in terms of SI units, that is, the test force in Newtons (N). However, in practice, the most commonly used force units are kilogram-force (kgf) and gram-force (gf). When Newton units of force are used, the force must be divided by the conversion factor 9.80665 N/kgf.

1.7?The test principles, testing procedures, and verification procedures are essentially identical for both the Vickers and Knoop hardness tests. The significant differences between the two tests are the geometries of the respective indenters, the method of calculation of the hardness numbers, and that Vickers hardness may be used at higher force levels than Knoop hardness.

Note 2:?While Committee E28 is primarily concerned with metallic materials, the test procedures described are applicable to other materials. Other materials may require special considerations, for example see C1326 and C1327 for ceramic testing.

1.8?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.9?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

국제분류(ICS)코드
페이지수 28
Edition 23

이력정보

No. 표준번호 표준명 발행일 상태
1 ASTM E92-23상세보기 Standard Test Methods for Vickers Hardness and Knoop Hardness of Metallic Materials 2023-07-01 표준
2 ASTM E92-23 REDLINE상세보기 Standard Test Methods for Vickers Hardness and Knoop Hardness of Metallic Materials 2023-07-01 표준
3 ASTM E92-17상세보기 Standard Test Methods for Vickers Hardness and Knoop Hardness of Metallic Materials 2017-04-01 구판
4 ASTM E92-17 REDLINE상세보기 Standard Test Methods for Vickers Hardness and Knoop Hardness of Metallic Materials 2017-04-01 구판
5 ASTM E92-16상세보기 Standard Test Methods for Vickers Hardness and Knoop Hardness of Metallic Materials 2016-02-01 구판
6 ASTM E92-82(2003)e1상세보기 Standard Test Method for Vickers Hardness of Metallic Materials 2003-01-10 구판
7 ASTM E92-82(2003)e2상세보기 Standard Test Method for Vickers Hardness of Metallic Materials (Withdrawn 2010) 2003-01-10 폐지(대체)
8 ASTM E92-82(2003)상세보기 Standard Test Method for Vickers Hardness of Metallic Materials 2003-01-10 구판
9 ASTM E92-82(1997)e3상세보기 Standard Test Method for Vickers Hardness of Metallic Materials 1997-01-01 구판

제공형태 닫기

  • PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)
  • 보안PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능
  • PRINT :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
  • BOOK :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
  • ZIP :

    압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)
  • CD/DVD :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)
  • DB :

    별도 정보 제공
  • HARDCOPY :

    해외 배송 상품, 최대 3주 소요
  • 바인더 :

    바인더 우편발송, 2~3일 소요
  • 온라인구독 :

    WEB 접속 후 실시간 열람, 출력(1년간)