한국표준정보망

회원가입 로그인 비회원(주문조회) 장바구니 이용안내

English
메뉴
검색 마이페이지 장바구니0

QUICK

닫기

TOP

해외표준 상세정보

관심표준 등록 : 표준업데이트 시 알림서비스

제공형태 더보기

  • KS

    표준

    판매

    ASTM D696-24 REDLINE

    Standard Test Method for Coefficient of Linear Thermal Expansion of Plastics Between ?30°C and +30°C with a Vitreous Silica Dilatometer
    • 발행일 : 2024-08-01
    • 발행기관 : ASTM
    즐겨찾기 장바구니 담기
    닫기

    상품이 장바구니에 담겼습니다.

    장바구니로 이동

    • [영어]PDF(레드라인) 131,600원

    • [영어]PRINT(레드라인) 131,600원

  • 레드라인이란?

    최신표준과 직전 구판표준의 변경내용을 포함하고 있는 버전. 구입 시 최신표준과 레드라인 두 개 파일을 제공합니다.

상세정보

분야
적용범위

1.1?This test method covers determination of the coefficient of linear thermal expansion for plastic materials having coefficients of expansion greater than 1??m/(m.°C) by use of a vitreous silica dilatometer. At the test temperatures and under the stresses imposed, the plastic materials shall have a negligible creep or elastic strain rate or both, insofar as these properties would significantly affect the accuracy of the measurements.

1.1.1?Test Method E228 shall be used for temperatures other than ?30°C and +30°C.

1.1.2?This test method shall not be used for measurements on materials with a very low coefficient of expansion (that is, less than 1 ?m/(m.°C)). For materials with a very low coefficient of expansion, interferometer or capacitance techniques are recommended.

1.1.3?A common alternative technique is thermomechanical analysis, as described in Test Method E831, which permits measurement of this property over a scanned temperature range.

1.2?The thermal expansion of a plastic is composed of a reversible component on which are superimposed changes in length due to changes in moisture content, curing, loss of plasticizer or solvents, release of stresses, phase changes, and other factors. This test method is intended for determining the coefficient of linear thermal expansion under the exclusion of these factors as far as possible. In general, it will not be possible to exclude the effect of these factors completely. For this reason, this test method can be expected to give only an approximation to the true thermal expansion.

1.3?The values stated in SI units are to be regarded as standard. The values in parentheses are for information only.

1.4?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

Note 1:?There is no known ISO equivalent to this standard.

1.5?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
국제분류(ICS)코드
페이지수 5
Edition 24

이력정보

No. 표준번호 표준명 발행일 상태
1 ASTM D696-24상세보기 Standard Test Method for Coefficient of Linear Thermal Expansion of Plastics Between ?30°C and +30°C with a Vitreous Silica Dilatometer 2024-08-01 표준
2 ASTM D696-24 REDLINE상세보기 Standard Test Method for Coefficient of Linear Thermal Expansion of Plastics Between ?30°C and +30°C with a Vitreous Silica Dilatometer 2024-08-01 표준
3 ASTM D696-16상세보기 Standard Test Method for Coefficient of Linear Thermal Expansion of Plastics Between −30°C and 30°C with a Vitreous Silica Dilatometer 2016-04-01 구판
4 ASTM D696-16 REDLINE상세보기 Standard Test Method for Coefficient of Linear Thermal Expansion of Plastics Between −30°C and 30°C with a Vitreous Silica Dilatometer 2016-04-01 구판
5 ASTM D696-08e1상세보기 Standard Test Method for Coefficient of Linear Thermal Expansion of Plastics Between −30°C and 30°C with a Vitreous Silica Dilatometer 2008-11-01 구판
6 ASTM D696-08상세보기 Standard Test Method for Coefficient of Linear Thermal Expansion of Plastics Between -30°C and 30°C With a Vitreous Silica Dilatometer 2008-11-01 구판
7 ASTM D696-03상세보기 Standard Test Method for Coefficient of Linear Thermal Expansion of Plastics Between -30°C and 30°C With a Vitreous Silica Dilatometer 2003-04-10 구판
8 ASTM D696-98상세보기 Standard Test Method for Coefficient of Linear Thermal Expansion of Plastics Between -30°C and 30°C With a Vitreous Silica Dilatometer 1998-02-10 구판

관련상품

  • 관련상품이 존재하지 않습니다.

다른 사람이 함께 구입한 상품

  • 함께 구입한 상품이 존재하지 않습니다.

추천 상품

제공형태 닫기

  • PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)

  • 보안PDF :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)* 단, 파일이동 및 복사 불가, 1회 다운로드 및 인쇄가능

  • PRINT :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

  • BOOK :

    인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)

  • ZIP :

    압축파일형태로 제공 (PDF, HTML, TXT, XLS 등으로 구성), 직접 파일 다운로드(마이페이지 확인)

  • CD/DVD :

    직접 파일 다운로드 및 인쇄(마이페이지 확인)

  • DB :

    별도 정보 제공

  • HARDCOPY :

    해외 배송 상품, 최대 3주 소요

  • 바인더 :

    바인더 우편발송, 2~3일 소요

  • 온라인구독 :

    WEB 접속 후 실시간 열람, 출력(1년간)